3. Attach the Latch Assembly (82) to the Left Upright (84) |
|
| 3 |
|
| ||
| with the two Latch Screws (56). Start both Latch Screws |
|
|
|
| ||
|
|
|
|
|
| ||
| before tightening either of them. Note: The Latch Screws |
|
|
|
|
| |
| may be preattached to the Left Upright. |
|
|
|
|
| |
|
|
|
|
|
| 56 | 82 |
|
|
|
|
|
|
| |
|
|
|
|
|
| 84 |
|
4. See step 6 and locate the four Upright Bolts (86). Loosen |
|
| 4a |
| 4b | ||
| the Upright Bolts two to three turns. |
|
|
| |||
|
|
|
|
|
| ||
| See drawing 4c. With the help of a second person, hold |
|
|
|
|
| |
| the Console Base (101) near the Uprights (80, 84). Look |
|
|
|
| ||
| under the Console Base and locate the wires on the |
|
|
|
|
| |
| sides of the Console Base. Make sure that the wires are |
|
|
| Correct | Incorrect | |
| not routed through the openings for the Trays (109, |
|
| ||||
| 111). Drawing 4a shows the correct route for the wires; |
| 4c |
|
| ||
| drawing 4b shows an incorrect route. |
|
|
|
| ||
|
|
|
|
|
| ||
| See drawing 4c. Cut the plastic ties holding the Wire |
|
|
| 111 |
| |
| Harness (74) and the pulse wire in the Uprights (80, 84). |
|
| 109 | |||
|
|
|
| ||||
| Connect the Wire Harness and the pulse wire to the |
|
|
|
|
| |
| wires on the sides of the Console Base (101). | Make sure |
|
|
|
| |
| to connect the connectors properly (see the inset |
|
|
| 101 |
| |
| drawings). IF THE CONNECTORS ARE NOT CON- |
|
|
| 81 | ||
|
|
|
| 75 | |||
| NECTED PROPERLY, THE CONSOLE MAY BE DAM- |
|
|
|
| ||
|
|
|
|
|
| ||
| AGED WHEN THE POWER IS TURNED ON. The con- |
|
|
| 80 |
| |
| nectors should slide together easily and snap into |
|
|
| 84 | ||
| place. | If the connectors do not slide together easily and |
|
|
|
| |
| snap into place, turn one connector and try again. Insert |
|
|
|
|
| |
| the excess Wire Harness and pulse wire up into the |
|
|
|
|
| |
| Console Base. |
|
|
|
|
| |
| Press the Right and Left Top Endcaps (75, 81) into the |
|
|
| 74 | Pulse | |
| Uprights (80, 84) as shown. |
|
|
| Wire | ||
5. | Set the Console Base (101) on the Uprights (80, 84). |
| Be | 5 |
| 101 | |
| careful not to pinch the Wires (not shown) in the |
|
|
| |||
|
|
|
|
|
| ||
| Uprights. | Attach the Console Base to each Upright with |
|
|
|
| 84 |
| two Console Bolts (76) and two Internal Star Washers |
|
|
|
| ||
| (77); start all four Console Bolts before tightening any of |
|
| 111 | 109 | ||
| them. |
|
|
|
| ||
|
|
|
|
|
|
| |
| Make sure that the Left and Right Trays (109, 111) are |
|
|
|
| ||
| pressed into the Console Base (101). |
|
|
|
| 77 | |
|
|
|
|
|
| 77 | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| 77 |
|
|
|
|
| 76 | 80 | 76 |
|
|
|
| 6 |
|
|
|