ProForm PFTL39908.0 manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 19

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 12. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

 

 

To reset the circuit breaker, wait for five minutes,

Tripped

Reset

and then press the switch back in.

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 17 to turn off the demo mode.

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

65

20

POWER CORD. Remove the three indicated M4.2 x

19mm Hood Screws (20) and two M5.5 x 25mm

 

 

 

Screws (25). Then, carefully remove the Motor Hood

 

25

 

(65).

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents On the WEB QUESTIONS?Model No. PFTL39908.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Page For your benefit, read this manual carefully before Before YOU BeginMake sure that the power cord is unplugged AssemblyExtra hardware may be included Do not tighten the Bolts yet See the upper inset drawing. Locate the wireOrient the Left Upright 53 so the indicated Small holes are on top as shown. AttachSee the left inset drawing. Identify the outer See the left inset drawing. Identify the twoOuter side of the Frame Spacer facing Right Upright Washer 9 do not tighten the Bolt yet Top ViewShould slide together easily and snap into Assembly 91. Make sure that no wires areWire. See the inset drawing. The connectors Again. if the Connectors are not CONPage Knob Spring Collar Large Hole Pin HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramStart the walking belt HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleSeconds- avoid moving Measure your heart rate if desiredTurn on the fan if desired HOW to USE a Speed Workout Make sure that the audio wire is fully plugged HOW to USE the Sound SystemInformation Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Unplug the Power CORD. If the walking belt Problem The walking belt slows when walked onBelt has shifted to the right, turn the left idler roller Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. PFTL39908.0105 Cage Nut Blue Wire, 2F 106 107 Isolator Userʼs Manual Exploded Drawing A-Model No. PFTL39908.0 Exploded Drawing B-Model No. PFTL39908.0 R0908A Exploded Drawing C-Model No. PFTL39908.0 R0908A Exploded Drawing D-Model No. PFTL39908.0 R0908A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents