7. Set the Console Assembly (91) face down on a | 7 | Console |
|
| |
soft surface to avoid scratching the Console |
|
| |||
Assembly. Hold the Right Handrail (33), which |
| Tie | Wire | 85 |
|
has a large hole in one side, near the Console. | Bracket |
| 10 | ||
Next, insert the console wire and the tie into the |
|
| 7 | ||
hole in the side of the Right Handrail (33). Using |
|
|
|
|
|
needlenose pliers, pull the console wire out of |
| Large |
|
| |
the hole near the bracket on the Right Handrail. | 33 |
|
| ||
Then, set the Right Handrail (33) on the Console | Hole |
|
| ||
Assembly (91). Make sure that no wires are |
| 91 |
|
|
|
pinched. Start an M5 x 16mm Screw (85) with a |
|
|
|
| |
M5 Star Washer (7) into the Right Handrail, and |
|
|
|
|
|
then start two M4.2 x 19mm Screws (10) into the |
|
|
|
|
|
Right Handrail. Tighten the M5 x 16mm Screw |
|
|
|
|
|
and then tighten the two M4.2 x 19mm |
|
|
|
|
|
Screws; do not overtighten the Screws. |
|
|
|
|
|
Attach the Left Handrail (not shown) to the |
|
|
|
|
|
Console Assembly (91) in the same way. |
|
|
|
|
|
Note: There are no wires on the left side. |
|
|
|
|
|
8. Remove the plastic ties from the Right Handrail | 8 |
|
|
|
|
(33) and the Left Handrail (not shown). Press the |
|
|
|
| |
two Cage Nuts (105) back into place if necessary |
|
|
|
|
|
(only one side is shown). With the help of a second |
|
|
|
|
|
person, hold the Console Assembly (91) near the | 33 |
| 91 |
|
|
Right Upright (54). |
|
|
| ||
Connect the Wire Harness (39) to the console |
|
| 105 |
|
|
wire. See the inset drawing. The connectors | 39 |
| Tie |
|
|
should slide together easily and snap into |
| Console |
|
| |
place. If they do not, turn one connector and try |
|
| Wire |
|
|
again. IF THE CONNECTORS ARE NOT CON- |
|
| Wire |
|
|
NECTED PROPERLY, THE CONSOLE MAY |
|
|
|
| |
BE DAMAGED WHEN THE POWER IS | 54 |
| Tie |
| 39 |
TURNED ON. Next, remove the wire tie from the |
|
|
| ||
Wire Harness. Insert the connectors and the ex- |
|
|
|
|
|
cess wire downward into the Right Upright (54). |
|
|
|
|
|
9. Attach the Console Assembly (91) to the Uprights | 9 | 91 |
|
|
|
(53, 54) with four M8 x 15mm Bolts (8) and four |
|
|
| ||
M8 Star Washers (5); do not fully tighten the |
|
|
|
|
|
Bolts yet. Make sure that no wires are |
|
|
|
|
|
pinched. |
|
|
|
|
|
|
| 5 | 8 | 8 | 5 53 |
| 54 |
|
| ||
| 9 |
|
|
|
|