ProForm PATL50707.0 user manual

Page 7

2.Have a second person hold the Base (52) in the position shown.

Identify the Left Upright (53) (the Right Upright [54] has a large hole near the lower end).

Hold the Left Upright (53) so the two small holes for the latch assembly are on top as shown. Insert two M10 x 58mm Bolts (2) into the bracket on the Left Upright. Attach the Left Upright to the Base (52) with the Bolts, two M10 Star Washers (9) and two M10 Jam Nuts (16).

Do not tighten the Nuts yet.

Attach the Right Upright (54) to the Base (52) in the same way.

3.Slide the two Wheel Housings (45) onto the Base (52). Attach each Wheel Housing with two M6 x 58mm Bolts (13), two M6 Washers (32), and two M6 Nuts (43).

4.Position the Base (52) as close to the front of the treadmill as possible, as shown.

See the upper inset drawing. Wrap the wire tie in the Right Upright (54) around the end of the Wire Harness (39). Then, pull the other end of the wire tie until the Wire Harness is extending from the upper end of the Right Upright. Secure the Wire Harness to the top of the Right Upright so that it will not fall inside.

See the lower inset drawing. Press the indicated Grommet (49) into the Right Upright (54).

2

 

 

 

 

9

 

 

2

 

 

 

54

 

16

 

 

 

 

 

9

 

9

Large

 

52

2

Hole

 

 

16

Small Holes

 

 

 

 

 

 

9

 

 

53

 

3

32

 

 

45

 

 

43

 

 

 

13

32

 

 

 

 

 

 

 

 

32

 

 

45

43

 

 

 

 

 

13

32

 

52

 

4

 

4a

 

 

39

39

54

Wire Tie

54

52

4b

54

49

39

52

7

Image 7
Contents Model No. PATL50707.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyPage See the left inset drawing. Identify the outer See the left inset drawing. Identify the twoOuter side of the Frame Spacer facing Do not tighten the Bolt yetConsole Wire Tie Bracket Large Hole Con sole Gas Spring. Be careful to avoid losing Knob Spring Collar Large Hole Pin HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power Change the incline of the treadmill as desired HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleRate will be shown. For the most accurate heart When you are finished exercising, removeAdjust the incline of the treadmill to the lowest When you fold the treadmill to the storage posiSelect one of the six speed workouts HOW to USE a Speed WorkoutHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop View Problem The walking belt slows when walked on Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description R0907ADescription Exploded Drawing A-Model No. PATL50707 Exploded Drawing B-Model No. PATL50707.0 Exploded Drawing C-Model No. PATL50707.0 Exploded Drawing D-Model No. PATL50707.0 Limited Warranty Ordering Replacement PartsIcon Authorized Dealer