ProForm PATL50707.0 user manual Console Wire Tie Bracket Large Hole Con sole

Page 9

7.Set the Console (91) face-down on a soft sur- face to avoid scratching the Console. Hold the Right Handrail (33), which has a large hole in the location shown, near the Console.

Next, insert the console wire and tie into the hole in the side of the Right Handrail (33). If necessary, use needlenose pliers to pull the console wire out of the hole near the bracket on the Right Handrail.

Then, set the Right Handrail (33) on the Console (91). Make sure that no wires are pinched. Start an M5 x 16mm Screw (85) with an M5 Star Washer (7) into the Right Handrail, and then start two M4.2 x 19mm Screws (10) into the Right Handrail. Tighten the M5 x 16mm Screw and then the two M4.2 x 19mm Screws; do not overtighten the Screws.

Attach the Left Handrail (not shown) to the Console (91) in the same way. Note: There are no wires on the left side.

8.See the upper inset drawing. If there is a guard on the end of the Console Wire, press the indicated tab and remove the guard with needlenose pliers. Discard the guard.

With the help of a second person, hold the Console (91) near the Right Upright (54).

Remove the colored tie from the Wire Harness (39). Connect the Wire Harness to the console wire. See the lower inset drawing. The con- nectors should slide together easily and snap into place. If they do not, turn one con- nector and try again. IF THE CONNECTORS

ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the connectors and excess wire into the Right Upright (54).

7

Console

 

 

 

 

 

 

Wire

85

 

 

 

 

 

Tie

7

 

 

Bracket

10

 

 

33

Large

 

 

 

Hole

 

 

 

91

 

 

8

 

 

 

Console

Wire

Tab 91

Guard

Console Wire

39

54

39

 

9. Attach the Console (91) to the Right Upright (54)

9

91

 

 

and the Left Upright (53) with six M8 x 15mm

 

 

 

 

 

 

 

 

 

Bolts (8) and six M8 Star Washers (5). Make

 

 

 

 

sure that no wires are pinched. Start all six

 

 

 

 

Handrail Bolts before tightening them.

 

 

 

 

With the help of a second person, carefully

 

 

 

 

lower the Uprights (53, 54) to the floor.

 

 

 

5

 

 

 

 

 

 

8

8

 

 

 

5

5

 

 

5

8

53

8

 

54

 

 

 

 

 

 

 

9

 

 

 

Image 9
Contents Model No. PATL50707.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyPage Outer side of the Frame Spacer facing See the left inset drawing. Identify the twoDo not tighten the Bolt yet See the left inset drawing. Identify the outerConsole Wire Tie Bracket Large Hole Con sole Gas Spring. Be careful to avoid losing Knob Spring Collar Large Hole Pin Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power Select the manual mode HOW to USE the Manual ModeInsert the key into the console Change the incline of the treadmill as desiredAdjust the incline of the treadmill to the lowest When you are finished exercising, removeWhen you fold the treadmill to the storage posi Rate will be shown. For the most accurate heartSelect one of the six speed workouts HOW to USE a Speed WorkoutHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyQty Description R0907ADescription Exploded Drawing A-Model No. PATL50707 Exploded Drawing B-Model No. PATL50707.0 Exploded Drawing C-Model No. PATL50707.0 Exploded Drawing D-Model No. PATL50707.0 Ordering Replacement Parts Limited WarrantyIcon Authorized Dealer