ProForm PATL40907.0 user manual Pull on the sleeve to make sure that it is locked into place

Page 11

14.Identify the Storage Latch (53). Remove the tie from the end of the tube. Make sure that the sleeve has been slid over the indicated hole and that the Latch Knob (54) is locked into the hole.

Pull on the sleeve to make sure that it is locked into place.

15.Raise the Frame (56) to the position shown.

Have a second person hold the Frame until this step is completed.

Orient the Storage Latch (53) so that the large barrel and the Latch Knob (54) are in the posi- tions shown. Attach the Latch Bracket (14) to the bracket on the Base (83) with two 3/8" x 2" Bolts

(4) and two 3/8" Nuts (8).

Attach the upper end of the Storage Latch (53) to the bracket on the Frame (56) with a 3/8" x 2" Bolt (4) and a 3/8" Nut (8). Note: It may be nec- essary to move the Frame back and forth to align the Storage Latch with the bracket.

Lower the Frame (56) (see HOW TO LOWER THE TREADMILL FOR USE on page 24).

14
		54
	Tube	Hole
	Tube
	Sleeve
		53
15	56
	56
	8	4
		4
		53
	54	Large
		Barrel
		14
	83	8
		8
		4

16.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 26 and 27).

11

Image 11

Contents Model No. PATL40907.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblySee the inset drawing. Tie the long tie Do not fully fold the Frame yetNot overtighten the Nut the Wheel must turn Freely Fully tighten the Bolts yet Be careful not to pinch the Upright WireFirmly tighten the Bolts Screws before tightening any of them Pull on the sleeve to make sure that it is locked into place PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeChange the incline of the treadmill as desired Turn on the fan if desired Measure your heart rate if desiredPress the Quick Start button to start the workout HOW to USE a Cross Training WorkoutSelect a cross training workout Continue the cross trainer workout Perform the first strength exercise when promptedSelect a classic aerobic workout HOW to USE a Classic Aerobic WorkoutComplete the workout. See steps 4 to 9 on Select the monthly challengeGet a monthly challenge goal Start the workoutInformation Mode HOW to Review Your Monthly Challenge LOGOptional Chest Pulse Sensor HOW to Adjust the Cushioning SystemHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description R1207AQty Exploded Drawing A-Model No. PATL40907.0 Exploded Drawing B-Model No. PATL40907.0 Exploded Drawing C-Model No. PATL40907.0 Exploded Drawing D-Model No. PATL40907.0 Icon Authorized Dealer Ordering Replacement PartsLimited Warranty