ProForm PATL40907.0 user manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own Phillips screwdriver

,

adjustable wrench

, rubber mallet

, and scissors

.

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included.

#8 x 1/2" Screw

#8 x 1/2" Washer Head

#8 x 3/4" Screw

#8 x 3/4"

 

#10 x 3/4"

(1)–2

Screw (112)–4

(12)–4

Handrail/Switch Screw

Screw (5)–2

 

 

 

(15)–2

 

 

#8 x 1" Tek Screw (2)–4

#10 Star Washer

 

 

 

 

 

3/8" Star Washer

 

 

 

(10)–2

 

 

3/8" Nut (8)–3

(9)–8

Base Pad Spacer (13)–2

 

 

3/8" x 1 1/4" Bolt (7)–4

3/8" x 2" Bolt (4)–3

Bolt Spacer (80)–4

 

 

 

 

3/8" x 4" Bolt (6)–4

 

 

 

1.Make sure that the power cord is unplugged.

Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4), and the shipping bracket (A) from the Base (83).

Repeat this step on the other side of the treadmill. Discard the shipping brackets.

1

83

A

4

8

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents QUESTIONS? Model No. PATL40907.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedDo not fully fold the Frame yet Not overtighten the Nut the Wheel must turn FreelySee the inset drawing. Tie the long tie Be careful not to pinch the Upright Wire Fully tighten the Bolts yetFirmly tighten the Bolts Screws before tightening any of them Pull on the sleeve to make sure that it is locked into place Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleChange the incline of the treadmill as desired Measure your heart rate if desired Turn on the fan if desiredHOW to USE a Cross Training Workout Select a cross training workoutPress the Quick Start button to start the workout Perform the first strength exercise when prompted Continue the cross trainer workoutHOW to USE a Classic Aerobic Workout Select a classic aerobic workoutStart the workout Select the monthly challengeGet a monthly challenge goal Complete the workout. See steps 4 to 9 onHOW to Review Your Monthly Challenge LOG Information ModeHOW to Adjust the Cushioning System Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R1207A Key No. Qty DescriptionQty Exploded Drawing A-Model No. PATL40907.0 Exploded Drawing B-Model No. PATL40907.0 Exploded Drawing C-Model No. PATL40907.0 Exploded Drawing D-Model No. PATL40907.0 Ordering Replacement Parts Limited WarrantyIcon Authorized Dealer
Top Page Image Contents