ProForm 620 user manual Troubleshooting, Problem The power turns off during use

Page 21

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the back cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 12. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the back cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 18 to turn off the demo mode.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. With the help of a second person, carefully tip the Uprights (74, 78) down.

There may be two #8 x 2" Screws (105) in the bot- tom of the Belly Pan (73). If there are, remove them. Note: A Phillips screwdriver with a shaft at least 5 in. (13 cm) long is required.

a

74

 

78

73

 

105

 

105

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents
Model No Serial No Assembly Operation Maintenance Part List and DrawingTable of Contents Important Precautions Page Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedNut the Wheel must turn freely. Discard See the inset drawing. Tie the long tieMake sure the Upright Wire 38 is not Fully tighten the Bolts yetNot fully fold the Frame yet Firmly tighten the Bolts Pull on the sleeve to make sure that it is locked into place Start all the Screws before tightening any of themRaise the Frame 56 to the position shown Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired Select a classic workout HOW to USE a Classic WorkoutSelect a weight loss workout HOW to USE the Weight Loss CenterInformation Mode HOW to USE the Stereo Sound SystemOptional Chest Pulse Sensor To purchase the optional chest pulse sensor, callHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R1107AIf a part is missing, call Exploded Drawing A-Model No Exploded Drawing B-Model No Exploded Drawing C-Model No Exploded Drawing D-Model No Get it fixed, at your home or ours ONE Year Full Warranty