ProForm 620 user manual Problem The walking belt slows when walked on

Page 22

Remove the key from the console and UNPLUG THE POWER CORD. Remove the three #8 x 3/4" Screws (12) and carefully pivot the Hood (57) off.

Locate the Reed Switch (64) and the Magnet (42) on the left side of the Pulley (43). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If neces- sary, loosen the Reed Switch Screw (12), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the tread- mill for a few minutes to check for a correct speed reading.

12

57

1/8 in.

12

42

64

43

Top

View

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2–3 in.

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the back cover of this manual.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Assembly Operation Maintenance Part List and Drawing Model No Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Nut the Wheel must turn freely. Discard Make sure that the power cord is unpluggedDo not fully fold the Frame yet See the inset drawing. Tie the long tieFully tighten the Bolts yet Make sure the Upright Wire 38 is notNot fully fold the Frame yet Firmly tighten the Bolts Start all the Screws before tightening any of them Pull on the sleeve to make sure that it is locked into placeRaise the Frame 56 to the position shown HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired HOW to USE a Classic Workout Select a classic workoutHOW to USE the Weight Loss Center Select a weight loss workoutOptional Chest Pulse Sensor HOW to USE the Stereo Sound SystemInformation Mode To purchase the optional chest pulse sensor, callHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R1107A Qty DescriptionIf a part is missing, call Exploded Drawing A-Model No Exploded Drawing B-Model No Exploded Drawing C-Model No Exploded Drawing D-Model No ONE Year Full Warranty Get it fixed, at your home or ours

620 specifications

The ProForm 620 is an advanced elliptical machine designed to provide an effective and comfortable workout experience. It combines a variety of features, innovative technologies, and ergonomic characteristics, making it an attractive option for fitness enthusiasts at any level.

One of the standout features of the ProForm 620 is its 18-inch stride length. This feature allows users to engage various muscle groups in the legs and glutes while also enhancing the overall cardiovascular workout. The machine is designed to accommodate users of different heights, ensuring a smooth, natural motion for everyone.

The ProForm 620 is equipped with an array of resistance levels, offering up to 24 different settings. This range allows users to gradually increase their workout intensity, making it suitable for both beginners and experienced fitness aficionados. With digital resistance adjustments, users can easily modify their workout without interrupting their rhythm.

An integral part of the ProForm 620 is its space-saving design. The machine features a folding frame, allowing for easy storage when not in use. This is particularly beneficial for those with limited workout space at home. The machine also has built-in transport wheels, making it easy to move from one location to another.

Incorporating technology, the ProForm 620 offers an interactive workout experience through its built-in smart display. The 5-inch backlit display provides essential workout statistics, such as time, distance, calories burned, and heart rate. Additionally, it supports Bluetooth connectivity, enabling users to sync with fitness apps and track their progress over time.

The ProForm 620 is also designed with a focus on comfort. Its oversized pedals provide ample space for feet, with a non-slip surface to enhance stability during workouts. The adjustable, ergonomic handlebar supports different grip positions, ensuring comfort during longer exercise sessions.

Furthermore, the machine is equipped with silent magnetic resistance technology, which minimizes noise during operation. This feature allows users to work out at any time without disturbing others in the household.

Overall, the ProForm 620 combines versatility, advanced technology, and ergonomic design to create an elliptical machine that meets the varying needs of users. Whether for weight loss, cardio training, or overall fitness, the ProForm 620 stands out as a solid choice for people seeking to enhance their workout experience at home.
Top Page Image Contents