ProForm PFEL04900 manual Drawing. Make sure that the negative ends, Battery clip, Ing the wires

Page 7

6.Slide an M8 Split Washer (58) and an M8 Washer (81) onto an Axle Screw (30). Tighten the Axle Screw into one end of the Incline Axle (29). Next, apply a small amount of the included grease to the Incline Axle.

Align the indicated tubes on the Incline Frame (5) with the tubes on the Base (1). Make sure that the Incline

Frame is turned so the V-shaped grooves are on top. Insert the Incline Axle (29) through the Incline Frame and the Base. Note: It may be helpful to tap the Incline Axle with a rubber mallet to insert it.

Slide an M8 Split Washer (58) and an M8 Washer (81) onto the other Axle Screw (30). Tighten the Axle Screw into the open end of the Incline Axle (29).

6

V-shaped Groove

	5
	58
	81
1	30
	30
Grease	Tubes

81

58

29	Tubes

30

7. The Console (87) requires two ÒAAÓ batteries (not

included). Alkaline batteries are recommended. To

install batteries, turn the console over and insert two

batteries into the battery clip as shown in the inset

drawing. Make sure that the negative ends of the

batteries (marked ÒÑÓ) are touching the springs in

the battery clip.

Attach a Plastic Tie (53) to the battery clip as shown.

Attach the Console (87) to the Console Base (49) with

four M4 x 16mm Screws (35), making sure that the

indicated wires are extending from the Console Base

(49). Be careful not to pinch the wires.

8. Connect the Extension Wire (51) to the corresponding

787

49

Wires

Batteries

53

Battery

Clip

35

wire on the Console (87).

Next, connect the two Pulse Wires (86) to the two

remaining wires on the Console (87). Note: Either

Pulse Wire can be attached to either wire on the

Console.

Next, connect the ground wire to the indicated hole in

the Upright (2) with an M4 x 16mm Screw (35).

Carefully feed the wires down into the Upright (2).

8

Console

Wires

86

51

87

49

35

Ground Wire

Attach the Console Base (49) to the Upright with four

M4 x 16mm Screws (35). Be careful to avoid pinch-

ing the wires.

35

35 2

7

Image 7

Contents Model No. PFEL04900 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Back Before YOU Begin Front Right SideM8 x 108mm Bolt 79Ð2 Axle Screw 30Ð2 AssemblyLocknut the Incline Bracket must pivot easily Drawing. Make sure that the negative ends Battery clipBe careful not to pinch the wires Ing the wiresIdentify the Left Pedal Arm. Next, identify the Left On it. Be careful not to confuse the Left Pedal ArmWith the Right Pedal Arm not shown look at Position of the round tube in the inset drawing toPage HOW to Adjust the Resistance HOW to USE the Elliptical CrosstrainerExercising on the Elliptical Crosstrainer Using the Upper Body Arms Incline AdjustmentDescription of the Console STEP-BY-STEP Console Operation HOW the Pacer Programs OperateMeasure your heart rate if desired HOW to Select Miles or KilometersFul not to pull On the wires Speed, time, dis- tance, lap, or calorie modeÑ RepeatedlyPulse Sensor TROUBLE-SHOOTING Maintenance and TROUBLE-SHOOTINGConsole TROUBLE-SHOOTING Workout Guidelines Conditioning GuidelinesExercise Intensity Unconditioned Conditioned Training Zone AGE BEATS/MINSuggested Stretches Page Key Qty Description Part LISTÑModel No. PFEL0490089 70 Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT