ProForm PFEL71032 user manual

Page 7

5.Identify the Left Handlebar (9), which is marked with a sticker. Insert the Left Handlebar into one of the Handlebar Legs (79); make sure that the Handlebar

Leg is turned so the hexagonal holes are on the indicated side. Attach the Left Handlebar to the Handlebar Leg with two M8 x 43mm Button Bolts (50) and two M8 Nylon Locknuts (46). Make sure that the

Nylon Locknuts are seated in the hexagonal holes. Do not fully tighten the Button Bolts yet.

Attach the Right Handlebar (not shown) to the other Handlebar Leg (not shown) in the same way.

6.Apply a generous amount of the included grease to the Pivot Axle (108) and to the two M8.5 Small Washers (53). Insert the Pivot Axle into the Upright (2) and center it. Reapply grease to both ends of the Pivot Axle.

Identify the Left and Right Handlebars (9, 10), which are marked with stickers. Slide a Handlebar Spacer

(25)onto the short tube on each Handlebar, and rotate the Handlebar Spacers so the small arrows are pointing toward the floor. Then, slide the Handlebars onto the Pivot Axle (108). Make sure that the Handlebars are on the correct sides.

Tighten an M8 x 25mm Patch Screw (22) with an M8.5 Small Washer (53) and a Wave Washer (119) into each end of the Pivot Axle (108). Orient the two Handlebar Caps (23) as shown, and press the small tabs on the Handlebar Caps into the two Handlebar Spacers (25).

7.Apply a thin film of grease to the shaft of a Union Bolt Set (27) and to the two Bushings (28) in the left Handlebar Leg (79).

Attach the left Handlebar Leg (79) to the left Flex Bar (14) with the Union Bolt Set (27).

See assembly step 5 above. Tighten the two M8 x 43mm Button Bolts (50) in the left Handlebar Leg (79).

Make sure that the M8 Nylon Locknuts (46) are seated in the hexagonal holes.

Repeat this step to attach the right Handlebar Leg (79) to the right Flex Bar (14).

5

 

 

 

9

 

 

 

 

 

Tube

 

 

 

46

 

50

 

Hexagonal

 

 

 

 

79

 

Holes

 

 

 

 

6

 

 

 

 

 

10

23

 

 

53

22

 

 

 

 

 

119

 

9

 

Tube

 

25

Grease

 

 

108

 

Tube

 

 

 

22 119

 

Arrow

 

23

 

 

 

25

 

 

 

Arrow

 

 

 

53

 

 

 

Grease

 

2

 

7

 

 

 

79

 

79

 

 

 

 

28

27

14

 

 

 

 

 

 

Grease

 

 

 

14

 

 

 

27

 

 

 

7

Image 7
Contents Model No. PFEL71032 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Leveling Foot Before YOU BeginFront BackAssembly Make sure Wire harnesses Do not get Pinched Wire Harnesses with the Button ScrewsDuring this Step Page Page Page HOW to Exercise on the Elliptical Crosstrainer HOW to USE the Elliptical CrosstrainerHOW to Adjust the Pedals Features of the Console HOW to USE the Manual Mode Sheets of plas Center dis Turn on the fan if desiredMeasure your heart rate if desired If there are thinFollow your progress with the displays HOW to USE a Smart ProgramSelect one of the Smart programs Begin pedaling to start the programHold the handgrip pulse sensor HOW to USE a Heart Rate ProgramSelect one of the Heart Rate programs Enter your age and a target heart rateHOW to Connect Your Portable CD Player HOW to Connect Your CD PLAYER, VCR, or ComputerHOW to Connect Your Home Stereo HOW to Connect Your Portable StereoHOW to Connect Your VCR HOW to Connect Your ComputerPressVCR. the play button on your CD player or HOW to USE Programs Directly from OUR WEB SiteHandgrip Pulse Sensor Troubleshooting Maintenance and TroubleshootingHOW to Move the Elliptical Crosstrainer HOW to Level the Elliptical CrosstrainerExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesKey Qty Description KeyDrawing Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT