JVC RX-DP9VBK Connecting Audio/Video Components, Enhance your audio system, Analog Connections

Page 12

Enhance your audio system

You can use this receiver as the pre-amplifier (control amplifier) when you connect power amplifiers to the PREOUT jacks on the rear panel, using cables with RCA pin plugs (not supplied).

•Connect the white plug to the audio left jack, and the red plug to the audio right jack.

Left front speaker

Right front speaker

Power amplifier

Center speaker

Connecting Audio/Video Components

You can connect the following audio/video components to this receiver. Refer also to the manuals supplied with your components.

Audio Components	Video Components
• Turntable	*
• Turntable	• DVD player
• CD player*	• TV*
• Cassette deck	*
• Cassette deck	• DBS tuner
or MD recorder*	• VCRs
• CD recorder*	• Video camera

*You can connect these components using the methods described in “Analog connections” (below) and in “Digital connections” (see page 14).

Analog Connections

Audio component connections

Use the cables with RCA pin plugs (not supplied).

•Connect the white plug to the audio left jack, and the red plug to the audio right jack.

RIGHT

FRONT

Power amplifier

LEFT

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.

SUB WOOFER

SURR

SURR

BACK

CENTER

Turntable

If a ground cable is provided for your turntable, connect the cable to the

RIGHT

LEFT

AUDIO

PHONO

CD

PREOUT

Power amplifier

screw marked (H) on the rear panel.

Turntable	To audio output

OUT

(REC)

TAPE

MD

IN

(PLAY)

OUT

(REC)

CDR

IN

(PLAY)

FRONT

SUB	CENTER
WOOFER	CENTER
SURR
(REAR)

R DVD L

Left / right Surround speakers

Note:

The above connection is for a turntable with an MM (moving-magnet) type cartridge.

Any turntables incorporating a small-output cartridge such as an MC (moving-coil) type must be connected to this receiver through a commercial head amplifier or step-up transformer. Direct connection may result in insufficient volume.

9

Image 12

Contents RX-DP9VBK Cautio -- STANDBY/ON switch 21.1 kg / 47 lbPage Table of Contents Features PrecautionsIntroduction Parts Identification Front PanelDisplay Window For more details, seeAnalog indicator Digital Auto indicatorSurround/DSP mode indicators Tuned indicatorRemote Control Signal transmission indicatorLights up when transmitting the remote control signals Setup MENU, Adjust MENU, SET, EXIT, %UP DOWN, @LEFT, #RIGHT Before Installation Connecting the FM and AM Antennas Checking the Supplied Accessories Getting StartedConnecting the Speakers AM Antenna ConnectionsTurn the loop until you have the best reception Speaker layoutBasic connecting procedure Connecting the surround back speakersConnecting the subwoofer speaker Important for the Front 1 Speakers connectionConnecting Audio/Video Components Enhance your audio systemAnalog Connections TurntableCD player CD recorderCassette deck or MD recorder VCRs VHS or VHS VCRVideo camera TV and/or DBS tuner DBS tunerDVD player Digital Connections Digital input terminalsDigital output terminal Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverSimple Operating Procedure Basic OperationsTurning the Power On and Off Standby Selecting the Source to PlaySpeaker and signal indicators on the display Front door while viewingPicture from a video component Press one of the source selecting buttonsAdjusting the Volume Activating the Front Speakers Selecting the Analog or Digital Input Mode Select this for the analog input modeAnalog indicator lights up Before you start, rememberAttenuating the Input Signal Turning Line Direct On and OffMuting the Sound Making Sounds Natural Changing the Source NameChanging the Display Brightness Using the Sleep Timer Basic adjustment auto memoryWhen the shut-off time comes To cancel the Sleep TimerTuning into Stations Manually Receiving Radio BroadcastsPress FM or AM Press UP or Down insideUsing Preset Tuning Selecting the FM Reception ModeBasic Settings Setup Menu ConfigurationOperation through On-Screen Display Menus Menu operation buttonsButton To do Menu Operating Procedure Press Setup MenuPress SET Set other items on the same submenu if necessarySelect this when a subwoofer is connected Select this when no subwoofer is usedFor subwoofer For measuring unitSetting the Bass Sounds-SUBWOOFER Setting the Dynamic Range -DYNAMIC Range Setting the Surround Sound Output -SURROUND SpeakerPreparing for THX Surround Modes-THX Setting the Digital Input Terminals -DIGITAL Setting the component connected to the digitalSetting the component video input terminals Preparing for the Component Video Input -COMPONENTTurning On and Off the Video Output -VIDEO Power Select this not to store the volume level settingTo recall the volume level To cancel the One Touch OperationSound Adjustments Adjustment Menu ConfigurationEx. When you press Adjust Menu Adjust MenuOn the front panel Press Adjust Menu Ex.When adjusting a DSP parameterWhen adjusting the parametric equalizer Adjusting the Speaker Channel Output Levels-LEVEL Adjusting the Parametric Equalizer -PARAMETRIC EQAdjusting the DSP Parameters -DSP Parameter Adjusting the Center Channel -CENTER ChannelUsing the Surround Modes Reproducing Theater AmbienceIntroducing the Surround Modes THX Surround EX Dolby Digital EX3D Headphone Mode DVD Multi Playback ModeDolby Surround Dolby Pro Logic DTS SurroundTo cancel the THX Surround To cancel the conventional Surround modeActivating the Surround Modes Select and play one of the following sound sourcesAdjusting the Surround Sounds Temporarily Using the DSP Modes Reproducing the Sound FieldIntroducing the DSP Modes Headphone Mode Without connecting the surround speakersActivating the DSP Modes If the center speaker is connected and activatedAdjusting the DSP Parameters Temporarily Using the DVD Multi Playback Mode Activating the DVD Multi Playback ModeEx. When you press DVD Multi Press DVD Multi so that DVD Multi appears on the displayCompu Link Remote Control System Same timePress the play 3 button on the CD player Text Compu Link Remote Control System CD player MD recorderDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerEx. When you press Text Display Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Text display operation buttonsPress Text Display while CD is selected as the source Press %/ Þto move to SEARCH, then pressPress %/ Þto move to Performer Then press SET Press SET againPress %/ Þto move to SEARCH, then press SET Press %/ Þto move To GENRE, then Press SETPress %/ Þto move To the genre you Want to search for On the SearchPress Text Display while MD is selected as the source Press %/ Þto move to the genre you want, then press SETTo insert a space, press To correct an incorrect characterAV Compu Link Remote Control System Connections 1 AV Compu Link ConnectionConnections 2 Video Cable Connection CaseAutomatic Selection of TV’s Input Mode Automatic Power On/OffOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD player CD player-changerTurntable CD recorderOperating Video Components VCR VCR connected to the VCR 1 jacksDVD player Changing the Preset Signal Codes Operating Other Manufacturers’ EquipmentEnter manufacturer’s code using Press and hold VCRPress VCR Buttons 1-9,If there are more than one code listed for your brand of CD Press DVDPress and hold Audio on Press CDManufactures codes for TV Manufacturer Codes Manufactures codes for DBS tuner Manufacturer CodesManufactures codes for Catv converter Manufacturer Codes Manufactures codes for VCR Manufacturer CodesTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAudio Tuning Range KHz to 1 710 kHz Usable Sensitivity Signal-to-Noise Ratio 50 dB 100 mV/mFM tuner IHF AM tunerAuthorized Service Centers Limited Warranty 0701NHMMDWJEIN

Related manuals

Manual 70 pages 29.03 Kb