JVC RX-DP9VBK manual Adjusting the Speaker Channel Output Levels-LEVEL

Adjusting the Speaker Channel Output Levels—LEVEL (1)

Notes:

• “TEST TONE” is not available if both speakers 1 and 2 are

LEVEL
TEST TONE	:OFF
FRONT L LEVEL:		0dB
CENTER LEVEL :		0dB
FRONT R LEVEL:		0dB
SURR R LEVEL :		0dB
SBACK R LEVEL:		0dB
SBACK L LEVEL:		0dB
SURR L LEVEL :		0dB
SUBWOOFER	:	0dB
:OPERATE		:BACK

Notes:

On this submenu, you can adjust the speaker channel output levels. While outputting the test tone, select a speaker channel and adjust its output level.

Once adjustment is done on this submenu, it is stored for each source when you change the source or when you turn off the receiver.

deactivated or if Surround mode is turned off.

• If “NO” or “NONE” is selected for a speaker on the SPEAKER

SETTING submenu (page 29), test tone does not come out of

the speaker.

7Adjusting the speaker channel output levels

Select and adjust the following speakers:

FRONT L LEVEL : Select this to adjust the left front speaker output level within the range of –20 dB to +10 dB, and – – – (nodB sound).

•The speaker level adjustments except the left/right front level and subwoofer level will be affected and be changed according to the Surround/DSP mode setting.

•You can show this submenu simply by pressing TEST button on the remote control. Test tone comes out of the activated speakers in sequence. (See page 42.)

7Adjustment procedure on this submenu

Adjustment is also possible without outputting the test tone. In this case, you can skip steps 1, 2 and 6 below.

1 Press Þor %(DOWN or UP) to select “TEST TONE.”

2 Press # or @(RIGHT or LEFT) to output the test tone. (See “Outputting the test tone” below.)

3 Press Þ or %(DOWN or UP) to select a speaker you want to adjust.

4 Press # or @(RIGHT or LEFT) to adjust the speaker output level.

5 Repeat step 3 and 4 to adjust the other speaker output levels.

6 After adjustment is finished, stop the test tone.

1 Press % or Þ(UP or DOWN) to select “TEST TONE.” 2 Press #or @(RIGHT or LEFT) to select “OFF.”

7Outputting the test tone

CAUTION:

Test tone is automatically fixed to 0 dB, but this level will be louder than you would expect.

Select one of the following.

•Test tone will be heard about three seconds after you select “AUTO” or “MANUAL.”

AUTO	: When this is selected, the test tone comes out of all
	the activated speakers in sequence (for 2 seconds
	each). The test tone comes out of the activated
	speakers in the following sequence:

Left front speaker = Center speaker = Right front speaker

=Right surround speaker = Right surround back speaker

=Left surround back speaker = Left surround speaker

=Subwoofer = (Back to the beginning)

MANUAL : When this is selected, the test tone comes out of only the speaker you select. (To select the speaker, see the right column.)

OFF : Select this to stop the test tone.

FRONT R LEVEL : Select this to adjust the right front speaker output level within the range of –20 dBto +10 dB, and – – – (nodB sound).

CENTER LEVEL : Select this to adjust the center speaker output level within the range of –10 dB to +10 dB.

SURR L LEVEL	: Select this to adjust the left surround
	speaker output level within the range of
	–10 dBto +10 dB.
SURR R LEVEL	: Select this to adjust the right surround
	speaker output level within the range of
	–10 dBto +10 dB.

SBACK L LEVEL : Select this to adjust the left surround back speaker output level within the range of –10 dBto +10 dB.

SBACK R LEVEL : Select this to adjust the right surround back speaker output level within the range of –10 dBto +10 dB.

SUBWOOFER : Select this to adjust the subwoofer output level within the range of –10 dB to +10 dB.

Note:

If “NO” or “NONE” is selected for a speaker on the SPEAKER

SETTING submenu (page 29), you cannot adjust its output level.

Adjusting the Parametric Equalizer —PARAMETRIC EQ (2)

		On this submenu, you can
PARAMETRIC EQ
		adjust equalization patterns
FRONT
		according to your preference.
CENTER
SURROUND		First, select the signal channel
SURROUND BACK
	:ENTER	(speaker) you want to adjust,
		then move to its adjustment
	:BACK
		screen.

Notes:

•If “NO” or “NONE” is selected for a speaker on the SPEAKER SETTING submenu (see page 29), you cannot select the corresponding channel.

•If THX Surround or DVD MULTI playback mode is in use, this submenu is not available.

37