JVC RX-DP9VBK manual Operating JVC’s Audio/Video Components, Operating Audio Components, Tuner

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK (SYNCHRO) jacks (see page 47) in addition to the connections using cables with RCA pin plugs (see pages 9 and 10).

•Aim the remote control directly at the remote sensor on the receiver.

•To operate a source with the remote control, the source must be selected using source selecting buttons on the remote control.

•To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 22.)

•Refer also to the manuals supplied with your components.

When using the remote control:

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode for a while (10 or 5 seconds).

–The CONTROL button can change the remote control operation mode without changing the source.

Each time you press the button, the remote control operation mode changes in the sequence—VCR1 =TAPE =CDR =CDDSC =(back to the beginning).

STANDBY ON

Tuner

You can always perform the following operations:

FM	: Tunes into the last selected FM station.
AM	: Tunes into the last selected AM station.
After pressing FM or AM, you can perform the following
	operations:
1 – 10, +10	: Selects a preset channel number directly.
	For channel number 5, press 5.
	For channel number 15, press +10, then 5.
	For channel number 20, press +10, then
	10.
TUNING UP/DOWN	: Tunes into stations.
FM MODE	: Changes the FM reception mode.

Sound control section (Amplifier)

You can always perform the following operations:

THX ON/OFF	: Turns on or off the THX Surround
	modes—THX Surround EX or THX
	Cinema.
SURROUND ON/OFF	: Turns on or off the conventional
	Surround modes—Dolby Digital,
	DTS Surround, and Dolby Pro
	Logic.
DSP MODE	: Selects the DSP modes.
TEST	: Turns on or off the test tone output.

TV/CATV/DBS VCR 1

STANDBY/ON STANDBY/ON

Ex. When you press FM.

After pressing SOUND, you can perform the following operations:

FRONT•L then LEVEL +/– : Adjusts the left front speaker channel output level.

FRONT•R then LEVEL +/– : Adjusts the right front speaker channel output level.

SUBWFR then LEVEL +/– : Adjusts the subwoofer output level.

CENTER then LEVEL +/– : Adjusts the center speaker channel output level.

SURR•L then LEVEL +/– : Adjusts the left surround speaker channel output level.

SURR•R then LEVEL +/– : Adjusts the right surround speaker channel output level.

SURR BK•L then LEVEL +/– : Adjusts the left surround back speaker channel output level.

SURR BK•R then LEVEL +/–: Adjusts the right surround back

	channel speaker output level.
EFFECT	: Selects the effect level.
ROOM SIZE	: Selects the room size.
LIVENESS	: Selects the liveness.
WALL	: Selects the wall type.
LINE DIRECT	: Turns on or off Line Direct.
CC CONVERTER	: Turns on or off CC Converter.

Notes:

•After adjusting sounds, press the corresponding source selecting button to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

•Each time you press LEVEL + or LEVEL –, the corresponding speaker name appears on the remote’s display.

55