JVC LVT1437-001A Connecting the FM and AM MW antennas, FM antenna connection, FM antenna supplied

Page 11

Connecting the FM and AM (MW) antennas

Do not connect the AC power plug to the wall outlet until all connections are completed.

AM (MW) loop antenna (supplied)

If FM reception is poor, connect an outdoor FM antenna (not supplied).

Snap the tabs on the loop into the slots of the base to assemble the AM (MW) loop antenna.

If AM (MW) reception is poor, connect an outdoor single vinyl- covered wire (not supplied).

AM LOOP

AM EXT

ANTENNA

FM 75

COAXIAL

FM antenna (supplied)

AM (MW) antenna connection

NOTES

Connect the AM (MW) loop antenna supplied to the AM LOOP terminals.

Connect the white cord to the AM EXT terminal, and connect the black cord to the H terminal.

Turn the loop until you have the best reception.

•If the reception is poor, connect an outdoor single vinyl-covered wire (not supplied) to the AM EXT terminal. Keep the AM (MW) loop antenna connected.

•If the AM (MW) loop antenna wire is covered with vinyl, remove the vinyl while twisting it as shown on the right.

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

FM antenna connection

Connect the FM antenna supplied to the FM 75 Ω COAXIAL terminal as a temporary measure.

Extend the supplied FM antenna horizontally.

•If the reception is poor, connect an outdoor FM antenna (not supplied). Before attaching a 75 Ω coaxial cable with a

connector (IEC or DIN 45325), disconnect the supplied FM antenna.

7

Image 11

Contents RX-D701S / RX-D702B European Union Information for Users on Disposal of Old EquipmentImportant for the U.K If in Doubt Consult a Competent ElectricianRegulatory information Above ALL Precautions FeaturesTable of Contents TV, VCR, DVR/DVD, FM/AM, USB, AUX, Video Remote controlWhen operating a DVD player, set the mode selector o to DVD Parts identificationSee pages in parentheses for details How to open the front doorFront panel Inside the front door Press down on PUSH-OPENRear panel Display windowGetting started Before InstallationPutting batteries in the remote control Checking the supplied accessoriesAntenna Connecting the FM and AM MW antennasFM antenna connection FM antenna suppliedConnecting the powered subwoofer Connecting the speakersSpeaker Layout Diagram Connecting the speakersHdmi Connecting video componentsBefore connecting video components Video conversion functionConnections Connecting a TVGreen Component video cable not supplied Blue Red Turn off all components before makingRed Connecting a DVD recorder or DVD playerStereo audio cable Monaural audio cable not supplied Signal currentWhen you enjoy sound recorded in DVD-Audio WhiteGreen Connecting a VCRScart cable not supplied Signal current Component video cable not supplied Hdmi cable not suppliedHdmi cable not supplied Connecting another video component to the Video in jacksComponent video cable not supplied Video camera, etc Connecting a video component to the AUX input jacksHow to open the front door Digital input terminals Connecting the power cordDigital audio connection Turn off all components before making connectionsFor USB Terminal USB connectionUSB Terminal How to install the USB driversUSB drivers are installed automatically Check if the drivers are correctly installedBasic operations Turn on the powerTo turn off the power into standby Press STANDBY/ON or Audio on the remote controlHdmi Digital Analog Adjust the volumeSelecting the video input setting Selecting the audio input settingTurning off the sounds temporarily Selecting the digital decode modeListening with headphones From the remote control only Press Dimmer repeatedlyMaking sounds natural Turning off the power with the Sleep TimerBasic adjustment of auto memory Signal and speaker indicators on the displayPress and hold Smart S. Setup until Setting UP flashes Basic settingsSBR SBL SL Menu operation buttons Basic setting itemsFrom the remote control Operation through on-screen display menusSee Setup menu configurationUsable buttons and their functions Menu operating procedureButton indications on the screen To select the desired submenu, press 5 or ∞ repeatedlyPress SET Setting the itemsSetting the speakers Setting subwoofer information-SUBWOOFERSpeaker distance Setting the surround back speakersSetting the speaker distance Initial setting S Back OUT 2SPKSelecting the main or sub channel Activating the EX/ES/PLIIx setting-EX/ES/ PLIIxSetting bass sound Setting subwoofer output-SUBWFR OUTMidnight OFF Using the Midnight mode-MIDNIGHTSetting the low frequency effect attenuator Setting the crossover frequency-CROSSOVERMemorizing the volume level for each source-ONE Touch OP Setting the Audio delay levelSuperimposing the menus Selecting the output video signalsSetting the Auto Function mode Basic adjustment items Sound adjustmentsAdjust Menu To select the desired submenu, press Or ∞ repeatedly To start the adjustment, pressPress Test to check the speakers’ output balance Adjusting the itemsAdjusting the speaker output levels Adjusting the virtual room size for DSP modes Adjusting the sound parameters for the Surround/DSP modesAdjusting the bass sounds Attenuating the input signal-INPUT ATTAdjusting the center tone-CENTER Tone Adjusting the liveness effect for DSP modesTuner operations Tuning in to stations manuallyUsing preset tuning To store the preset stationsTo tune in a preset station Selecting the FM reception modePress Display while listening to an FM station Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? RDS indicatorPress PTY Search while listening to an FM station To search for a program using the PTY codesSearching for a program by PTY codes PTY codesDescription of the PTY codes Display TA News Info TA/NEWS TA/INFOTA Traffic Announcement in your area Dolby Digital Creating realistic sound fieldsReproducing theatre ambience Introducing the Surround modesDTS About other digital signalsDigital Acoustic Processor DAP modes All Channel Stereo mode ALL CH Stereo3D Headphone mode Introducing the DSP modesAuto Using the Surround/DSP modesAbout the DSP modes Virtual Surround BackSelecting the Surround/DSP modes When you select Auto SurroundFrom the remote control Select and play any source Turn Multi JOG to select the Surround/DSP mode you wantREW Operating other JVC productsVCR Channel +DVD Menu Changing the remote control code for DVD recorderDVD recorder or DVD player Release DVR/DVDRelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Manufacturers’ codes for TVManufacturers’ codes for VCR Changing the transmittable signals for operating a VCRRelease VCR Try to operate your VCR by pressing VCRChanging the transmittable signals for operating a STB Sound and picture TroubleshootingPower Problem Possible Cause SolutionCorrect antenna Remote control TunerAM MW tuner SpecificationsAmplifier FM tuner IHF1105RYMMDWJEIN Victor Company of Japan, Limited