JVC 1105RYMMDWJEIN, LVT1437-001A Specifications, Amplifier, FM tuner IHF, AM MW tuner, General

Page 62

Specifications

Designs and specifications are subject to change without notice.

Amplifier

Output Power

At stereo operation:

 

Front channels:

130 W per channel, min. RMS, driven into

 

6 at 1 kHz with no more than 0.8% total

 

harmonic distortion. (IEC268-3/DIN)

At surround operation:

 

Front channels:

130 W per channel, min. RMS, driven into

 

6 at 1 kHz with no more than 0.8% total

 

harmonic distortion.

Center channel:

130 W, min. RMS, driven into 6 at 1 kHz,

 

with no more than 0.8% total harmonic

 

distortion.

Surround channels: 130 W per channel, min. RMS, driven into 6 at 1 kHz, with no more than 0.8% total harmonic distortion.

Surround back channels:

130 W per channel, min. RMS, driven into 6 at 1 kHz, with no more than 0.8% total harmonic distortion.

Audio

Audio Input Sensitivity/Impedance:

DVR/DVD, VCR, VIDEO, TV:

300 mV/47 k

Audio Input (DIGITAL IN)*:

Coaxial: DIGITAL IN 1(DVR/DVD):

0.5 V(p-p)/75

Optical: DIGITAL IN 2(VIDEO), 3(TV):

–21 dBm to –15 dBm (660 nm ±30 nm)

USB: USB WIRELESS

USB TERMINAL

*Corresponding to Linear PCM, Dolby Digital, and DTS (with sampling frequency—32 kHz, 44.1 kHz, 48 kHz).

Audio Output Level:

 

DVR, VCR:

300 mV

Signal-to-Noise Ratio (’66 IHF/DIN): 80 dB/56 dB

Frequency Response (6 ):

20 Hz to 20 kHz (±1 dB)

Bass Boost:

+4 dB ±1 dB at 100 Hz

Equalization (at DSP operation):

Center frequency:

63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz

Control range:

±8 dB

Video

Video Input Sensitivity/Impedance:

Composite video: DVR/DVD, VCR, VIDEO:

 

1 V(p-p)/75

S-video: DVR/DVD, VCR, VIDEO:

Y (luminance):

1 V(p-p)/75

C (chrominance, burst):

0.3 V(p-p)/75

RGB: DVR/DVD, VCR:

0.7 V(p-p)/75

Component: DVR/DVD, VIDEO (VCR):

Y (luminance):

1 V(p-p)/75

PB, PR:

0.7 V(p-p)/75

Video Output Level/Impedance:

 

Composite video: DVR, VCR, TV:

 

1 V(p-p)/75

S-video: DVR, VCR, TV:

 

Y (luminance):

1 V(p-p)/75

C (chrominance, burst):

0.3 V(p-p)/75

RGB: TV:

0.7 V(p-p)/75

Component: MONITOR OUT:

 

Y (luminance):

1 V(p-p)/75

PB, PR:

0.7 V(p-p)/75

Synchronization:

Negative

HDMI

HDMI Input (Ver. 1.1): VIDEO (VCR), DVR/DVD

HDMI Output (Ver. 1.0): MONITOR OUT

FM tuner (IHF)

Tuning Range:

87.50 MHz to 108.00 MHz

Usable Sensitivity:

 

Monaural:

17.0 dBf (1.9 µV/75 )

50 dB Quieting Sensitivity:

 

Monaural:

21.3 dBf (3.2 µV/75 )

Stereo:

41.3 dBf (31.8 µV/75 )

Stereo Separation at REC OUT:

35 dB at 1 kHz

AM (MW) tuner

Tuning Range:522 kHz to 1 629 kHz

General

Power Requirements:

AC 230 V , 50 Hz

Power Consumption:

180 W (at operation)

1.2W (in standby mode)

Dimensions (W x H x D): 435 mm x 91.5 mm x 371 mm

Mass:

7.8 kg

USB WIRELESS SYSTEM

The USB wireless transmitter supplied with this receiver supports Direct Sequence Spreading Spectrum (DSSS) using 2.4 GHz frequency band.

58

Image 62
Contents RX-D701S / RX-D702B If in Doubt Consult a Competent Electrician Information for Users on Disposal of Old EquipmentImportant for the U.K European UnionRegulatory information Above ALL Features PrecautionsTable of Contents Parts identification Remote controlWhen operating a DVD player, set the mode selector o to DVD TV, VCR, DVR/DVD, FM/AM, USB, AUX, VideoInside the front door Press down on PUSH-OPEN How to open the front doorFront panel See pages in parentheses for detailsDisplay window Rear panelChecking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedFM antenna supplied Connecting the FM and AM MW antennasFM antenna connection AntennaConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferVideo conversion function Connecting video componentsBefore connecting video components HdmiTurn off all components before making Connecting a TVGreen Component video cable not supplied Blue Red ConnectionsConnecting a DVD recorder or DVD player RedWhite Monaural audio cable not supplied Signal currentWhen you enjoy sound recorded in DVD-Audio Stereo audio cableComponent video cable not supplied Hdmi cable not supplied Connecting a VCRScart cable not supplied Signal current GreenHdmi cable not supplied Connecting another video component to the Video in jacksComponent video cable not supplied Video camera, etc Connecting a video component to the AUX input jacksHow to open the front door Turn off all components before making connections Connecting the power cordDigital audio connection Digital input terminalsUSB connection For USB TerminalCheck if the drivers are correctly installed How to install the USB driversUSB drivers are installed automatically USB TerminalPress STANDBY/ON or Audio on the remote control Turn on the powerTo turn off the power into standby Basic operationsSelecting the audio input setting Adjust the volumeSelecting the video input setting Hdmi Digital AnalogFrom the remote control only Press Dimmer repeatedly Selecting the digital decode modeListening with headphones Turning off the sounds temporarilySignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Making sounds naturalBasic settings Press and hold Smart S. Setup until Setting UP flashesSBR SBL SL Operation through on-screen display menus Basic setting itemsFrom the remote control Menu operation buttonsSetup menu configuration SeeTo select the desired submenu, press 5 or ∞ repeatedly Menu operating procedureButton indications on the screen Usable buttons and their functionsSetting subwoofer information-SUBWOOFER Setting the itemsSetting the speakers Press SETInitial setting S Back OUT 2SPK Setting the surround back speakersSetting the speaker distance Speaker distanceSetting subwoofer output-SUBWFR OUT Activating the EX/ES/PLIIx setting-EX/ES/ PLIIxSetting bass sound Selecting the main or sub channelSetting the crossover frequency-CROSSOVER Using the Midnight mode-MIDNIGHTSetting the low frequency effect attenuator Midnight OFFSetting the Audio delay level Memorizing the volume level for each source-ONE Touch OPSuperimposing the menus Selecting the output video signalsSetting the Auto Function mode Sound adjustments Basic adjustment itemsAdjust Menu To start the adjustment, press To select the desired submenu, press Or ∞ repeatedlyPress Test to check the speakers’ output balance Adjusting the itemsAdjusting the speaker output levels Attenuating the input signal-INPUT ATT Adjusting the sound parameters for the Surround/DSP modesAdjusting the bass sounds Adjusting the virtual room size for DSP modesAdjusting the liveness effect for DSP modes Adjusting the center tone-CENTER ToneTo store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsSelecting the FM reception mode To tune in a preset stationRDS indicator Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? Press Display while listening to an FM stationPTY codes To search for a program using the PTY codesSearching for a program by PTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes Display TA News Info TA/NEWS TA/INFOTA Traffic Announcement in your area Introducing the Surround modes Creating realistic sound fieldsReproducing theatre ambience Dolby DigitalAbout other digital signals DTSIntroducing the DSP modes All Channel Stereo mode ALL CH Stereo3D Headphone mode Digital Acoustic Processor DAP modesVirtual Surround Back Using the Surround/DSP modesAbout the DSP modes AutoTurn Multi JOG to select the Surround/DSP mode you want When you select Auto SurroundFrom the remote control Select and play any source Selecting the Surround/DSP modesChannel + Operating other JVC productsVCR REWRelease DVR/DVD Changing the remote control code for DVD recorderDVD recorder or DVD player DVD MenuManufacturers’ codes for TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Release TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRChanging the transmittable signals for operating a STB Problem Possible Cause Solution TroubleshootingPower Sound and pictureRemote control Tuner Correct antennaFM tuner IHF SpecificationsAmplifier AM MW tunerVictor Company of Japan, Limited 1105RYMMDWJEIN