JVC LVT1437-001A, 1105RYMMDWJEIN manual USB connection, For USB Terminal

Page 21

USB connection

This receiver is equipped with a USB terminal on the front panel and a USB WIRELESS ANTENNA terminal on the rear. You can enjoy the sound reproduced through your PC with either of the following methods:

1connecting a USB wireless antenna (supplied) to the USB WIRELESS ANTENNA terminal and a USB wireless

transmitter (supplied) to your PC. (USB WIRELESS)

2connecting your PC to the USB terminal with a USB cable (not supplied). (USB TERMINAL)

When you connect your PC for the first time, follow the procedure below.

•Remember you cannot send any signal or data to your PC from this receiver.

•Use USB extension cable (supplied) if it is difficult to connect the transmitter directly to the USB connector or the transmitter becomes obstacle to other USB connectors.

IMPORTANT:

Check if your PC equipped with the CD-ROM drive is running on Windows® 98 SE*, Windows® Me*, Windows® 2000* or Windows® XP* and prepare its CD-ROM.

Preparation

1For USB WIRELESS

Be sure to make USB WIRELESS communication before connection and installation of the receiver. During the procedure, you need to check the status of the lamp on the rear of the receiver (turning on or flashing).

1Connect the antenna to the USB WIRELESS ANTENNA terminal on the rear panel.

• Tighten the screw with the antenna upright.

USB wireless

antenna

(supplied)

USB WIRELESS

ANTENNA

ON ID LEARNING

2Turn on your PC.

•If the PC has been turned on, quit all the applications now running.

3Connect the USB wireless transmitter to the USB connector of the PC.

Before connecting the transmitter to the PC, remove the cover of the transmitter.

When you connect the transmitter, the USB drivers are installed. The POWER and PLAYER lamp on the transmitter light up.

USB wireless

transmitter (supplied)

PC

 

USB WIRELESS TRANSMITTER

 

USB WIRELESS TRANSMITTER

POWER ID PLAYER

4Turn on the receiver, then slide the USB WIRELESS switch on the rear to “ID LEARNING,” and select the source as “USB WIRELESS.”

When you slide the switch, the lamp in the switch starts flashing.

5Set the volume to minimum.

IMPORTANT:

Always set volume to “0” when connecting or disconnecting the other equipment.

6Press and hold ID on the transmitter to make a wireless communication with the receiver.

When you press and hold the button, the ID lamp on the transmitter flashes.

USB WIRELESS TRANSMITTER

CHANNEL

ID

POWER

ID

PLAYER

When the receiver recognizes the transmitter, the lamp on the rear of the receiver stops flashing and lights up.

7Slide the switch on the receiver to “ON.”

• If you do not, no sound signal is transmitted to the receiver.

NOTES

•The signal-reachable distance is about 30 m, but it may differ depending on the operating conditions and circumstances.

•The PLAYER lamp on the transmitter keeps flashing when starting the playback software in your PC.

•If no signals are transmitted from the transmitter for about 30 minutes, the transmitter enters “sleep” mode. The “L” and “R” indicators go off from the display.

•Though the transmitter may become hot, it is not a malfunction.

2For USB TERMINAL

1Turn on your PC.

•If the PC has been turned on, quit all the applications now running.

2Turn on the receiver, and select the source as “USB TERMINAL.”

3Set the volume to minimum.

IMPORTANT:

Always set volume to “0” when connecting or disconnecting the other equipment.

4Connect the receiver to the PC using a USB cable (not supplied).

USB

PC

USB cable (not supplied)

•Use “USB series A plug to B plug” cable when connecting.

CONTINUED ON THE NEXT PAGE

17

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RX-D701S / RX-D702B Important for the U.K Information for Users on Disposal of Old EquipmentIf in Doubt Consult a Competent Electrician European UnionRegulatory information Above ALL Precautions FeaturesTable of Contents When operating a DVD player, set the mode selector o to DVD Remote controlParts identification TV, VCR, DVR/DVD, FM/AM, USB, AUX, VideoFront panel How to open the front doorInside the front door Press down on PUSH-OPEN See pages in parentheses for detailsRear panel Display windowPutting batteries in the remote control Before InstallationChecking the supplied accessories Getting startedFM antenna connection Connecting the FM and AM MW antennasFM antenna supplied AntennaSpeaker Layout Diagram Connecting the speakersConnecting the speakers Connecting the powered subwooferBefore connecting video components Connecting video componentsVideo conversion function HdmiGreen Component video cable not supplied Blue Red Connecting a TVTurn off all components before making ConnectionsRed Connecting a DVD recorder or DVD playerWhen you enjoy sound recorded in DVD-Audio Monaural audio cable not supplied Signal currentWhite Stereo audio cableScart cable not supplied Signal current Connecting a VCRComponent video cable not supplied Hdmi cable not supplied GreenConnecting another video component to the Video in jacks Component video cable not suppliedHdmi cable not supplied Connecting a video component to the AUX input jacks How to open the front doorVideo camera, etc Digital audio connection Connecting the power cordTurn off all components before making connections Digital input terminalsFor USB Terminal USB connectionUSB drivers are installed automatically How to install the USB driversCheck if the drivers are correctly installed USB TerminalTo turn off the power into standby Turn on the powerPress STANDBY/ON or Audio on the remote control Basic operationsSelecting the video input setting Adjust the volumeSelecting the audio input setting Hdmi Digital AnalogListening with headphones Selecting the digital decode modeFrom the remote control only Press Dimmer repeatedly Turning off the sounds temporarilyBasic adjustment of auto memory Turning off the power with the Sleep TimerSignal and speaker indicators on the display Making sounds naturalPress and hold Smart S. Setup until Setting UP flashes Basic settingsSBR SBL SL From the remote control Basic setting itemsOperation through on-screen display menus Menu operation buttonsSee Setup menu configurationButton indications on the screen Menu operating procedureTo select the desired submenu, press 5 or ∞ repeatedly Usable buttons and their functionsSetting the speakers Setting the itemsSetting subwoofer information-SUBWOOFER Press SETSetting the speaker distance Setting the surround back speakersInitial setting S Back OUT 2SPK Speaker distanceSetting bass sound Activating the EX/ES/PLIIx setting-EX/ES/ PLIIxSetting subwoofer output-SUBWFR OUT Selecting the main or sub channelSetting the low frequency effect attenuator Using the Midnight mode-MIDNIGHTSetting the crossover frequency-CROSSOVER Midnight OFFMemorizing the volume level for each source-ONE Touch OP Setting the Audio delay levelSelecting the output video signals Setting the Auto Function modeSuperimposing the menus Basic adjustment items Sound adjustmentsAdjust Menu To select the desired submenu, press Or ∞ repeatedly To start the adjustment, pressAdjusting the items Adjusting the speaker output levelsPress Test to check the speakers’ output balance Adjusting the bass sounds Adjusting the sound parameters for the Surround/DSP modesAttenuating the input signal-INPUT ATT Adjusting the virtual room size for DSP modesAdjusting the center tone-CENTER Tone Adjusting the liveness effect for DSP modesUsing preset tuning Tuning in to stations manuallyTo store the preset stations Tuner operationsTo tune in a preset station Selecting the FM reception modeWhat information can RDS signals provide? Using the Radio Data System RDS to receive FM stationsRDS indicator Press Display while listening to an FM stationSearching for a program by PTY codes To search for a program using the PTY codesPTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TA News Info TA/NEWS TA/INFO TA Traffic Announcement in your areaDisplay Reproducing theatre ambience Creating realistic sound fieldsIntroducing the Surround modes Dolby DigitalDTS About other digital signals3D Headphone mode All Channel Stereo mode ALL CH StereoIntroducing the DSP modes Digital Acoustic Processor DAP modesAbout the DSP modes Using the Surround/DSP modesVirtual Surround Back AutoFrom the remote control Select and play any source When you select Auto SurroundTurn Multi JOG to select the Surround/DSP mode you want Selecting the Surround/DSP modesVCR Operating other JVC productsChannel + REWDVD recorder or DVD player Changing the remote control code for DVD recorderRelease DVR/DVD DVD MenuOperating other manufacturers’ products Changing the transmittable signals for operating a TVManufacturers’ codes for TV Release TVRelease VCR Changing the transmittable signals for operating a VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRChanging the transmittable signals for operating a STB Power TroubleshootingProblem Possible Cause Solution Sound and pictureCorrect antenna Remote control TunerAmplifier SpecificationsFM tuner IHF AM MW tuner1105RYMMDWJEIN Victor Company of Japan, Limited
Top Page Image Contents