JVC LVT1437-001A, 1105RYMMDWJEIN manual Remote control Tuner, Correct antenna

Page 61

Remote control

Tuner

PROBLEM

 

POSSIBLE CAUSE

SOLUTION

Remote control does not operate as

The remote control is not ready for your

Set the mode selector correctly, then press

you intend.

intended operation.

the corresponding source selecting button

 

 

 

before operation.

 

 

 

Remote control does not work.

There is an obstruction hiding the remote

Remove the obstruction.

 

sensor on the receiver.

 

 

 

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

 

 

The mode selector is set to the incorrect

Set the mode selector to the proper

 

position.

position.

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

reception.

 

 

your dealer.

 

 

 

 

 

The station is too far away.

Select another station.

 

 

 

 

 

The wrong antenna is being used.

Check with your dealer to be sure you have

 

 

 

the correct antenna.

 

 

 

 

 

Antennas are not connected properly.

Check the connections.

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

 

traffic.

57

Page 60 Page 62
Image 61
Page 60 Page 62
Contents RX-D701S / RX-D702B Important for the U.K Information for Users on Disposal of Old EquipmentIf in Doubt Consult a Competent Electrician European UnionRegulatory information Above ALL Precautions FeaturesTable of Contents When operating a DVD player, set the mode selector o to DVD Remote controlParts identification TV, VCR, DVR/DVD, FM/AM, USB, AUX, VideoFront panel How to open the front doorInside the front door Press down on PUSH-OPEN See pages in parentheses for detailsRear panel Display windowPutting batteries in the remote control Before InstallationChecking the supplied accessories Getting startedFM antenna connection Connecting the FM and AM MW antennasFM antenna supplied AntennaSpeaker Layout Diagram Connecting the speakersConnecting the speakers Connecting the powered subwooferBefore connecting video components Connecting video componentsVideo conversion function HdmiGreen Component video cable not supplied Blue Red Connecting a TVTurn off all components before making ConnectionsRed Connecting a DVD recorder or DVD playerWhen you enjoy sound recorded in DVD-Audio Monaural audio cable not supplied Signal currentWhite Stereo audio cableScart cable not supplied Signal current Connecting a VCRComponent video cable not supplied Hdmi cable not supplied GreenComponent video cable not supplied Connecting another video component to the Video in jacksHdmi cable not supplied How to open the front door Connecting a video component to the AUX input jacksVideo camera, etc Digital audio connection Connecting the power cordTurn off all components before making connections Digital input terminalsFor USB Terminal USB connectionUSB drivers are installed automatically How to install the USB driversCheck if the drivers are correctly installed USB TerminalTo turn off the power into standby Turn on the powerPress STANDBY/ON or Audio on the remote control Basic operationsSelecting the video input setting Adjust the volumeSelecting the audio input setting Hdmi Digital AnalogListening with headphones Selecting the digital decode modeFrom the remote control only Press Dimmer repeatedly Turning off the sounds temporarilyBasic adjustment of auto memory Turning off the power with the Sleep TimerSignal and speaker indicators on the display Making sounds naturalPress and hold Smart S. Setup until Setting UP flashes Basic settingsSBR SBL SL From the remote control Basic setting itemsOperation through on-screen display menus Menu operation buttonsSee Setup menu configurationButton indications on the screen Menu operating procedureTo select the desired submenu, press 5 or ∞ repeatedly Usable buttons and their functionsSetting the speakers Setting the itemsSetting subwoofer information-SUBWOOFER Press SETSetting the speaker distance Setting the surround back speakersInitial setting S Back OUT 2SPK Speaker distanceSetting bass sound Activating the EX/ES/PLIIx setting-EX/ES/ PLIIxSetting subwoofer output-SUBWFR OUT Selecting the main or sub channelSetting the low frequency effect attenuator Using the Midnight mode-MIDNIGHTSetting the crossover frequency-CROSSOVER Midnight OFFMemorizing the volume level for each source-ONE Touch OP Setting the Audio delay levelSetting the Auto Function mode Selecting the output video signalsSuperimposing the menus Basic adjustment items Sound adjustmentsAdjust Menu To select the desired submenu, press Or ∞ repeatedly To start the adjustment, pressAdjusting the speaker output levels Adjusting the itemsPress Test to check the speakers’ output balance Adjusting the bass sounds Adjusting the sound parameters for the Surround/DSP modesAttenuating the input signal-INPUT ATT Adjusting the virtual room size for DSP modesAdjusting the center tone-CENTER Tone Adjusting the liveness effect for DSP modesUsing preset tuning Tuning in to stations manuallyTo store the preset stations Tuner operationsTo tune in a preset station Selecting the FM reception modeWhat information can RDS signals provide? Using the Radio Data System RDS to receive FM stationsRDS indicator Press Display while listening to an FM stationSearching for a program by PTY codes To search for a program using the PTY codesPTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TA Traffic Announcement in your area TA News Info TA/NEWS TA/INFODisplay Reproducing theatre ambience Creating realistic sound fieldsIntroducing the Surround modes Dolby DigitalDTS About other digital signals3D Headphone mode All Channel Stereo mode ALL CH StereoIntroducing the DSP modes Digital Acoustic Processor DAP modesAbout the DSP modes Using the Surround/DSP modesVirtual Surround Back AutoFrom the remote control Select and play any source When you select Auto SurroundTurn Multi JOG to select the Surround/DSP mode you want Selecting the Surround/DSP modesVCR Operating other JVC productsChannel + REWDVD recorder or DVD player Changing the remote control code for DVD recorderRelease DVR/DVD DVD MenuOperating other manufacturers’ products Changing the transmittable signals for operating a TVManufacturers’ codes for TV Release TVRelease VCR Changing the transmittable signals for operating a VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRChanging the transmittable signals for operating a STB Power TroubleshootingProblem Possible Cause Solution Sound and pictureCorrect antenna Remote control TunerAmplifier SpecificationsFM tuner IHF AM MW tuner1105RYMMDWJEIN Victor Company of Japan, Limited
Top Page Image Contents