JVC RX-884RBK manual Getting Started, FM Antenna Connections, AM MW/LW Antenna Connections

Page 10

Getting Started

English

Connecting the FM and AM (MW/LW) Antennas

FM Antenna Connections

A	ANTENNA	75	B	ANTENNA	75
		FM			FM
		COAXIAL			COAXIAL
		GND			GND
	AM	AM		AM
	LOOP	AM		LOOP	AM
		EXT			EXT
			FM Antenna
ANTENNA			Extend the FM wire antenna horizontally.
	FM 75
	COAXIAL

Note:

If reception is poor, connect the outside antenna.

Before attaching a 75Ω coaxial cable (the kind with a round wire going to an outside antenna), disconnect the supplied FM wire antenna.

GND

AM

LOOP

AM

EXT

Outside FM Antenna Cable

A.Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75Ω COAXIAL terminal as temporary measure.

B.Using the Standard Type Connector (Not Supplied)

A standard type connector (IEC or DIN45325) should be connected to the FM 75Ω

COAXIAL terminal.

AM (MW/LW) Antenna Connections

ANTENNA

FM 75

COAXIAL

GND

AM LOOP

AM

EXT

1

Turn the loop until you have the best reception.

AM (MW/LW) Loop Antenna

		Snap the tabs on the loop
		into the slots of the base to
	3	assemble the AM (MW/
2	3	LW) loop.

Notes:

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

•If reception is poor, connect an outdoor single vinyl- covered wire to the AM EXT terminal. (Keep the AM (MW/ LW) loop antenna connected.)

Outdoor single vinyl- covered wire

5

Image 10

Contents RX-884RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-884RBK Table of Contents Using the DSP Modes Selecting Your Favorite SEA Mode Creating Your Own SEA ModeParts Identification Front Panel Remote Control3 4 5 678 90 = Locations Getting StartedGeneral Handling the receiverFM Antenna Connections Connecting the FM and AM MW/LW AntennasGetting Started AM MW/LW Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the rear and center speakers Connecting the subwoofer speakerAbout the speaker impedance Case 1 When you connect only one set of front speakersCase 2 When you connect two sets of front speakers Use front speakers with 4 16 ohm impedanceAudio Components Video Components Connecting Audio/Video ComponentsAnalog connections Audio component connectionsConnecting the TV and/or DBS tuner Video component connectionsConnecting DVD player Connecting VCRsDigital connections Digital 1 coaxial ForPress Power to set it in the Ñoff position Connecting the Power CordTo shut off the power completely Putting Batteries in the Remote ControlBasic Operations From the remote controlWhat are the following indicators? On the front panelPress one of the source selecting buttons directly Adjusting the VolumeBasic Operations Selecting different sources for picture and soundListening only with headphones From the remote control onlyOn the front panel only Display changes to show the current setting Attenuating the Input SignalAdjusting the Subwoofer Output Level Keys are activated for sound adjustmentsSelecting the DBS tuner as the source Basic SettingsSelecting the Input Mode Changing the Source NameSetting the Subwoofer Information Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessFront, Center, and Rear Speaker Setting Digital Input Digital in Terminal SettingSetting the Speakers for the DSP Modes Press Setting repeatedly until Front SPK FrontRear Delay Time Setting Center Delay Time SettingCrossover Frequency Setting Low Frequency Effect Attenuator Setting Dynamic Range Compression SettingTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsSelecting the FM Reception Mode To erase a stored preset stationTo tune in a preset station Receiving Radio BroadcastsFlashing Assigning Names to Preset StationsPress Tuner PRESET, while a character you want is Character is flashing after you have assigned a nameWhat Information Can RDS Signals Provide? Using the RDS Radio Data System to Receive FM StationsTo show the RDS signals To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes To stop searching any time during the processOn the display while PTY Select is flashing Press PTY Search while listening to an FMStation Display gives you the PTY codes described to RightTraffic Announcement in your area Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goes offSelecting Your Favorite SEA Mode Using the SEA ModesTo cancel the SEA mode To recall your own SEA adjustment Using the SEA ModesCreating Your Own SEA Mode To erase a stored adjustmentOn the DAP mode Using the DSP ModesOn the 3D-PHONIC mode On Surround modePress DSP Mode Using the DSP ModesUsing the 3D-PHONIC Modes Turn Multi JOG until the mode 3D Action or 3DTo cancel the 3D-PHONIC mode As you turn it, the effect level changes as followsYou want appears on the display Press Surround Mode repeatedly until the mode 3DAction or 3D DIGITAL, 3D DRAMA, or 3D Theater Press Effect to select the effect levelUsing the DAP Modes Adjust the speaker output levels as follows To cancel the DAP modePress Surround Mode repeatedly until the mode you Want appears on the displayPress Surround Mode repeatedly until PRO Logic Using the Dolby Digital and Dolby Pro Logic ModesOr Dolby Digital appears on the display Press Test to start checking the speaker output balance To cancel the Surround modePress Cntr Tone to select the center tone level you want Turn Multi JOG to select the center tone level you want Press Dolby Surround so that the lamp on the buttonLights up Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode To cancel the Theater Surround mode Press Cntr Tone to select the center tone level you wantDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Selecting the Source to Play Also see Using the On-Screen MenusWhen you select OSD, see Selecting the Different Sources for Picture and SoundAttenuating the Input Signal Also see Adjusting the Front Speaker Output Balance Also seeListening at Low Volume Loudness Also see Sound Control menu appears on the TVFor 3D-PHONIC modes Using the On-Screen MenusAdjusting the Subwoofer Output Level Also see For DAP modes Live CLUB, Dance CLUB, HALL, PavilionFor Dolby Digital Selecting Your Favorite SEA Mode Also seeFor Dolby Surround Pro Logic For Theater Surround and Digital Theater SurroundBasic Settings Creating Your Own SEA Mode Also seePress SET to store the setting into the SEA Usermode Storing the Preset Stations Also see Operating the TunerCharacter entry screen appears Assigning Names to the Preset Stations Also seeTuner Control menu appears again Checking the RDS Information Also see RDS Information menu appearsAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemWhat is a CD Text? Disc Search Only for CD PlayerText Compu Link Remote Control System Showing the Disc Information on the TV ScreenPress SET again Searching a Disc Only for the CD playerSearch a disc by its performer Going back to the Performer Search screen Press ExitPress on Screen Control %/ Þ to move to GENRE, then press Going back to the Disc Title Search screen Press ExitSearch a disc by its genre Genre Search screen appearsUser File screen appears on the TV Using your own User FilesGoing back to the User File screen Press Exit Title Input Performer screen appears on the TV Entering the Disc InformationFor the CD Player with the disc memory function To move to Shift , then press SETEnter the disc title, referring to steps 3 and 4 on For the MD recorderEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Cassette deck CD player-changerTurntable MD recorderREC Operating JVC’s Audio/Video ComponentsVCR1 the VCR connected to the VCR1 jacks DVD playerSets the input mode either TV or Adjusts the volumeTurns on or off the TV Operating Other Manufactures’ Components Following buttons can be used for operating the TV10, 0, 100++10 Pauses Operating Other Manufactures’ ComponentsStarts playback Try to operate your VCR by pressing VCR1Manufacturers’ codes for TV MTC Manufacturers’ codes for Catv converters 000, 037, 081 Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM