JVC RX-884RBK manual Digital connections, Digital 1 coaxial For

Page 17

Digital connections

This receiver is equipped with three DIGITAL IN terminals — one digital coaxial terminal and two digital optical terminals.

To enjoy Dolby Digital, you have to connect the source components using the DIGITAL IN terminals.

You can connect any component to any one of the digital terminals using the digital coaxial cable (not supplied) or digital optical cable (not supplied).

English

DBS tuner

DBS

DVD player

DVD

When the component has a digital coaxial output terminal, connect it to the DIGITAL 1 (DBS) terminal, using the digital coaxial cable (not supplied).

DIGITAL IN

PCM/DOLBY DIGITAL

Notes:

• When shipped from the

factory, the DIGITAL IN

terminals has been set for use

with the following

components.

– DIGITAL 1 (coaxial): For

CD player

MD recorder

When the component has a digital optical output terminal, connect it to the DIGITAL 2 (DVD) or DIGITAL 3 (CD) terminal, using the digital optical cable (not supplied).

Before connecting a digital optical cable, unplug the protective plug.

DIGITAL 1 (DBS)

DIGITAL 2 (DVD)

DIGITAL 3 (CD)

DBS tuner

– DIGITAL 2 (optical): For

DVD player

– DIGITAL 3 (optical): For CD

player

• When you want to operate the

CD player or MD recorder

using the COMPU LINK

remote control system,

connect the target component

also as described in “Analog

connections” (see page 9).

IMPORTANT:

•When connecting the DVD player or the DBS tuner using the digital terminal, you also need to connect it to the video jack (either composite video terminal or S-video terminal) on the rear. Without connecting it to the video jack, you can view no playback picture.

•After connecting the above components using the DIGITAL IN terminals, set the following correctly if necessary.

–Select the digital input mode correctly. For details, see “Selecting the Input Mode” on page 18.

–Set the digital input (DIGITAL IN) terminal setting correctly. For details, see “Digital Input (DIGITAL IN) Terminal Setting” on page 20.

12

Image 17

Contents RX-884RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-884RBK Table of Contents Selecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the DSP Modes3 4 5 678 90 = Front Panel Remote ControlParts Identification General Getting StartedLocations Handling the receiverGetting Started Connecting the FM and AM MW/LW AntennasFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the subwoofer speaker Connecting the rear and center speakersCase 2 When you connect two sets of front speakers Case 1 When you connect only one set of front speakersAbout the speaker impedance Use front speakers with 4 16 ohm impedanceAnalog connections Connecting Audio/Video ComponentsAudio Components Video Components Audio component connectionsVideo component connections Connecting the TV and/or DBS tunerConnecting VCRs Connecting DVD playerDigital 1 coaxial For Digital connectionsTo shut off the power completely Connecting the Power CordPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlWhat are the following indicators? From the remote controlBasic Operations On the front panelBasic Operations Adjusting the VolumePress one of the source selecting buttons directly Selecting different sources for picture and soundOn the front panel only From the remote control onlyListening only with headphones Adjusting the Subwoofer Output Level Attenuating the Input SignalDisplay changes to show the current setting Keys are activated for sound adjustmentsSelecting the Input Mode Basic SettingsSelecting the DBS tuner as the source Changing the Source NameAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Listening at Low Volume LoudnessSetting the Speakers for the DSP Modes Digital Input Digital in Terminal SettingFront, Center, and Rear Speaker Setting Press Setting repeatedly until Front SPK FrontCrossover Frequency Setting Center Delay Time SettingRear Delay Time Setting Dynamic Range Compression Setting Low Frequency Effect Attenuator SettingTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To erase a stored preset stationSelecting the FM Reception Mode Receiving Radio BroadcastsPress Tuner PRESET, while a character you want is Assigning Names to Preset StationsFlashing Character is flashing after you have assigned a nameTo show the RDS signals Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes To search for a program using the PTY codesTo continue searching after the first stop To stop searching any time during the processStation Press PTY Search while listening to an FMOn the display while PTY Select is flashing Display gives you the PTY codes described to RightReceiver enters EON standby mode Switching to a Broadcast Program of Your Choice TemporarilyTraffic Announcement in your area NewsPress EON so that the program type TA/NEWS/INFO goes off To stop listening to the program selected by EONTo cancel the SEA mode Using the SEA ModesSelecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the SEA ModesTo recall your own SEA adjustment To erase a stored adjustmentOn the 3D-PHONIC mode Using the DSP ModesOn the DAP mode On Surround modeUsing the 3D-PHONIC Modes Using the DSP ModesPress DSP Mode Turn Multi JOG until the mode 3D Action or 3DAs you turn it, the effect level changes as follows To cancel the 3D-PHONIC modeAction or 3D DIGITAL, 3D DRAMA, or 3D Theater Press Surround Mode repeatedly until the mode 3DYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes Press Surround Mode repeatedly until the mode you To cancel the DAP modeAdjust the speaker output levels as follows Want appears on the displayOr Dolby Digital appears on the display Using the Dolby Digital and Dolby Pro Logic ModesPress Surround Mode repeatedly until PRO Logic Press Cntr Tone to select the center tone level you want To cancel the Surround modePress Test to start checking the speaker output balance Lights up Press Dolby Surround so that the lamp on the buttonTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode Press Cntr Tone to select the center tone level you want To cancel the Theater Surround modeDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 When you select OSD, see Using the On-Screen MenusSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundListening at Low Volume Loudness Also see Adjusting the Front Speaker Output Balance Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVAdjusting the Subwoofer Output Level Also see Using the On-Screen MenusFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionFor Dolby Surround Pro Logic Selecting Your Favorite SEA Mode Also seeFor Dolby Digital For Theater Surround and Digital Theater SurroundPress SET to store the setting into the SEA Usermode Creating Your Own SEA Mode Also seeBasic Settings Operating the Tuner Storing the Preset Stations Also seeTuner Control menu appears again Assigning Names to the Preset Stations Also seeCharacter entry screen appears RDS Information menu appears Checking the RDS Information Also seeRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingWhat is a CD Text? Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen Text Compu Link Remote Control SystemSearch a disc by its performer Searching a Disc Only for the CD playerPress SET again Going back to the Performer Search screen Press ExitSearch a disc by its genre Going back to the Disc Title Search screen Press ExitPress on Screen Control %/ Þ to move to GENRE, then press Genre Search screen appearsGoing back to the User File screen Press Exit Using your own User FilesUser File screen appears on the TV For the CD Player with the disc memory function Entering the Disc InformationTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the song title, referring to steps 3 and 4 on For the MD recorderEnter the disc title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Turntable CD player-changerCassette deck MD recorderVCR1 the VCR connected to the VCR1 jacks Operating JVC’s Audio/Video ComponentsREC DVD playerTurns on or off the TV Adjusts the volumeSets the input mode either TV or Following buttons can be used for operating the TV Operating Other Manufactures’ Components10, 0, 100++10 Starts playback Operating Other Manufactures’ ComponentsPauses Try to operate your VCR by pressing VCR1Manufacturers’ codes for TV MTC Manufacturers’ codes for Catv converters 000, 037, 081 Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM