JVC RX-884RBK manual Creating Your Own SEA Mode Also see, Basic Settings

Page 56

Using the On-Screen Menus

English

Creating Your Own SEA Mode (Also see page 33)

1.Press any button of ON SCREEN CONTROL % / Þ/ @/ #once. The MAIN MENU appears on the TV.

2. Press ON SCREEN CONTROL % / Þ to move to “SOUND CONTROL,” then press @ / #.

The SOUND CONTROL menu appears.

3. Press ON SCREEN CONTROL %/ Þ to move to “SEA,” then press @ / #.

The SEA menu appears.

4. Press ON SCREEN CONTROL %/ Þ to move to “SEA ADJUST,” then press @ / #.

The SEA ADJUST menu appears.

5.Press ON SCREEN CONTROL % / Þ / @/ # to adjust the SEA mode as you want.

@/ # : Select the frequency ranges.

%/ Þ: Adjust the frequency levels.

6.Press SET to store the setting into the SEA USERMODE.

• If you press EXIT, without pressing SET in this step, you can return to the SEA menu. (The adjustment you have made is active but not stored.)

7.When you finish, press EXIT repeatedly until the menu disappears from the TV.

Basic Settings

1.Press any button of ON SCREEN CONTROL % / Þ/ @/ #once. The MAIN MENU appears on the TV.

2. Press ON SCREEN CONTROL %/ Þ to move to “SETTING,” then press

@/ #.

The SETTING 1 or SETTING 2 menu appears.

3. Press ON SCREEN CONTROL %/ Þ to the setting item you want to adjust.

• To go to the SETTING 2 menu, move to “NEXT PAGE,” then press @ / #.

• To go back to the SETTING 1 menu, move to “PREVIOUS PAGE,” then press @ / #.

On the SETTING 1 and 2 menus, you can do the following:

“SUBWOOFER”:

Set the subwoofer information (See page 19).

“FRONT SPK”:

Set the front speaker information ( See page 20).

“CENTER SPK”:

Set the center speaker information

(See page 20).

“REAR SPK”:

Set the rear speaker information (See page 20).

“CNTR DELAY”:

Adjust the delay time of the center speaker output (See page 21).

“REAR DELAY”:

Adjust the delay time of the rear speaker output (See page 21).

“CROSSOVER”:

Set the crossover frequency

(See page 21).

“LFE ATT.”:

Set the low frequency effect attenuator level (See page 22).

“COMP.”:

Set the dynamic range compression

(See page 22).

“DIGITAL 1/2/3”:

Set the digital input terminal

(See page 20).

MAIN MENU

MAIN MENU

SOURCE :VCR1￿

VISUAL :VCR1￿

MODE :OFF￿

￿

**

TUNERSOUND CONTROLCONTROL￿￿

**

**

SETTING ￿

**

**￿

 

**

￿:ENTER

VOLUME : 20

SOUND CONTROL menu

SOUND CONTROL

￿

** SURROUND LEVEL￿ **

**￿ SEA￿ **

BAL.:CNTR￿

LOUDNESS : OFF￿

INPUT ATT : NORMAL￿

SUBWFR LEVEL: 0dB￿ ￿

NEXT PAGE

 

 

 

 

 

 

 

 

 

 

 

 

:ENTER

SEA menu

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEA MODE

:ROCK￿

 

**￿

SEA ADJUST￿ **

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

 

100

 

 

 

1k 10kHz

￿:OPERATE

SEA ADJUST menu

SEA ADJUST

SEA USERMODE

100 1k 10kHz

SET:MEMORY￿

SETTING 1 menu

SETTING 1

 

 

SUBWOOFER

: NO￿

 

FRONT

SPK

: LARGE￿

 

CENTER

SPK

: SMALL￿

REAR

 

SPK

: LARGE￿

CNTR DELAY

: 3msec￿

REAR DELAY

: 5msec￿

￿

￿ NEXT

 

 

**

PAGE

**

:ENTER

SETTING 2 menu

SETTING 2

CROSSOVER :100Hz￿

LFE ATT. : 0dB￿

COMP. : OFF￿

DIGITAL 1 : DBS￿

DIGITAL 2 : CD￿

DIGITAL 3 : MD￿

￿

** PREVIOUS PAGE **

￿￿

:ENTER

51

Image 56
Contents RX-884RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-884RBK Table of Contents Using the DSP Modes Selecting Your Favorite SEA Mode Creating Your Own SEA Mode3 4 5 678 90 = Front Panel Remote ControlParts Identification Getting Started GeneralLocations Handling the receiverConnecting the FM and AM MW/LW Antennas Getting StartedFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the rear and center speakers Connecting the subwoofer speakerCase 1 When you connect only one set of front speakers Case 2 When you connect two sets of front speakersAbout the speaker impedance Use front speakers with 4 16 ohm impedanceConnecting Audio/Video Components Analog connectionsAudio Components Video Components Audio component connectionsConnecting the TV and/or DBS tuner Video component connectionsConnecting DVD player Connecting VCRsDigital connections Digital 1 coaxial ForConnecting the Power Cord To shut off the power completelyPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlFrom the remote control What are the following indicators?Basic Operations On the front panelAdjusting the Volume Basic OperationsPress one of the source selecting buttons directly Selecting different sources for picture and soundOn the front panel only From the remote control onlyListening only with headphones Attenuating the Input Signal Adjusting the Subwoofer Output LevelDisplay changes to show the current setting Keys are activated for sound adjustmentsBasic Settings Selecting the Input ModeSelecting the DBS tuner as the source Changing the Source NameBasic Settings Adjusting the Front Speaker Output BalanceSetting the Subwoofer Information Listening at Low Volume LoudnessDigital Input Digital in Terminal Setting Setting the Speakers for the DSP ModesFront, Center, and Rear Speaker Setting Press Setting repeatedly until Front SPK FrontCrossover Frequency Setting Center Delay Time SettingRear Delay Time Setting Low Frequency Effect Attenuator Setting Dynamic Range Compression SettingTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo erase a stored preset station To tune in a preset stationSelecting the FM Reception Mode Receiving Radio BroadcastsAssigning Names to Preset Stations Press Tuner PRESET, while a character you want isFlashing Character is flashing after you have assigned a nameTo show the RDS signals Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? To search for a program using the PTY codes Searching for a Program by PTY CodesTo continue searching after the first stop To stop searching any time during the processPress PTY Search while listening to an FM StationOn the display while PTY Select is flashing Display gives you the PTY codes described to RightSwitching to a Broadcast Program of Your Choice Temporarily Receiver enters EON standby modeTraffic Announcement in your area NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goes offTo cancel the SEA mode Using the SEA ModesSelecting Your Favorite SEA Mode Using the SEA Modes Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing the DSP Modes On the 3D-PHONIC modeOn the DAP mode On Surround modeUsing the DSP Modes Using the 3D-PHONIC ModesPress DSP Mode Turn Multi JOG until the mode 3D Action or 3DTo cancel the 3D-PHONIC mode As you turn it, the effect level changes as followsPress Surround Mode repeatedly until the mode 3D Action or 3D DIGITAL, 3D DRAMA, or 3D TheaterYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes To cancel the DAP mode Press Surround Mode repeatedly until the mode youAdjust the speaker output levels as follows Want appears on the displayOr Dolby Digital appears on the display Using the Dolby Digital and Dolby Pro Logic ModesPress Surround Mode repeatedly until PRO Logic Press Cntr Tone to select the center tone level you want To cancel the Surround modePress Test to start checking the speaker output balance Press Dolby Surround so that the lamp on the button Lights upTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode To cancel the Theater Surround mode Press Cntr Tone to select the center tone level you wantDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Using the On-Screen Menus When you select OSD, seeSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundAdjusting the Front Speaker Output Balance Also see Listening at Low Volume Loudness Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVUsing the On-Screen Menus Adjusting the Subwoofer Output Level Also seeFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionSelecting Your Favorite SEA Mode Also see For Dolby Surround Pro LogicFor Dolby Digital For Theater Surround and Digital Theater SurroundPress SET to store the setting into the SEA Usermode Creating Your Own SEA Mode Also seeBasic Settings Storing the Preset Stations Also see Operating the TunerTuner Control menu appears again Assigning Names to the Preset Stations Also seeCharacter entry screen appears Checking the RDS Information Also see RDS Information menu appearsCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingText Compu Link Remote Control System What is a CD Text?Displaying the Disc Information on the TV screen Disc Search Only for CD PlayerText Compu Link Remote Control System Showing the Disc Information on the TV ScreenSearching a Disc Only for the CD player Search a disc by its performerPress SET again Going back to the Performer Search screen Press ExitGoing back to the Disc Title Search screen Press Exit Search a disc by its genrePress on Screen Control %/ Þ to move to GENRE, then press Genre Search screen appearsGoing back to the User File screen Press Exit Using your own User FilesUser File screen appears on the TV Entering the Disc Information For the CD Player with the disc memory functionTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the song title, referring to steps 3 and 4 on For the MD recorderEnter the disc title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components CD player-changer TurntableCassette deck MD recorderOperating JVC’s Audio/Video Components VCR1 the VCR connected to the VCR1 jacksREC DVD playerTurns on or off the TV Adjusts the volumeSets the input mode either TV or Operating Other Manufactures’ Components Following buttons can be used for operating the TV10, 0, 100++10 Operating Other Manufactures’ Components Starts playbackPauses Try to operate your VCR by pressing VCR1Manufacturers’ codes for TV MTC Manufacturers’ codes for Catv converters 000, 037, 081 Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM