JVC RX-884RBK manual From the remote control, Using the Theater Surround Mode

Page 48

Using the DSP Modes

English

Using the Theater Surround Mode

Once you have adjusted the Theater Surround mode, this receiver memorizes the adjustment. To activate the Theater Surround mode, follow the procedure below.

From the remote control:

1. Select and play the source encoded with Dolby Digital (bearing the mark

) or with Dolby Surround (bearing the mark DOLBY SURROUND ).

D I G I T A L

When you play back the source encoded with Dolby Digital and select the digital input for that source, the ÙDIGITAL indicator lights up on the display.

SURROUND

2. Press SURROUND MODE repeatedly until “THEATER”MODE or “DIG-THEATER” appears on the display.

The DSP and THEATER indicators also light up on the display.

Each time you press the button, the DSP modes change as follows:

When the digital input is selected to play the source encoded with Dolby Digital:

DOLBY DIGITAL DIG-THEATER

OFF 3D DIGITAL HEADPHONE

For other sources:

PRO LOGIC THEATER LIVE CLUB DANCE CLUB HALL

OFF

PAVILION

3D THEATER 3D DRAMA 3D ACTION HEADPHONE

If you need to make any adjustment, go to the following steps.

3. Press SOUND CONTROL.

SOUND

CONTROL

 

10 keys are activated for sound adjustments.

4. Press TEST to start checking the speaker output balance.

TEST

 

 

 

 

 

 

 

 

 

 

 

 

“TEST TONE L” starts flashing on the display, and a test

4

 

 

tone comes out of the speakers in the following order:

 

 

 

 

 

 

 

TEST TONE L

 

TEST TONE C

 

 

TEST TONE R

 

 

 

 

 

(Left front speaker)

 

(Center speaker)

(Right front speaker)

 

 

 

 

TEST TONE LS

 

TEST TONE RS

 

 

 

 

 

 

(Left rear speaker)

 

 

 

 

 

 

 

 

(Right rear speaker)

 

 

 

 

 

 

 

 

L

C R

The speaker indicators also light on the display while the test tone

 

 

 

comes out of the speakers.

 

 

 

 

 

 

 

 

LS

RS

L: Lights when the test tone comes out of the left front speaker.

C:Lights when the test tone comes out of the center speaker.

R:Lights when the test tone comes out of the right front speaker. RS: Lights when the test tone comes out of the right rear speaker. LS: Lights when the test tone comes out of the left rear speaker.

IMPORTANT:

Output the test tone while playing back an audio source.

With the DVD digital input selected as the source, no test tone may come out while no signal is input to this receiver.

Test tone comes out even while playing back a source encoded with Dolby Digital. In this case, the PRO LOGIC indicator lights up on the display.

Notes:

To enjoy the software encoded with Dolby Digital, you must connect the source component using the digital terminal on the rear of this receiver.

The Surround mode is not used with the other DSP modes such as the DAP mode and 3D-PHONIC mode. When the Surround mode is turned on, the other DSP mode, if used, will be turned off.

Notes on the indications:

The PRO LOGIC indicator lights up when the Dolby Pro Logic decoder built in this receiver is activated.

The Dolby Pro Logic decoder is used not only for the analog sources but also for the sources encoded with Dolby Digital in the following cases:

When only front channel signals are encoded.

When front channel and

monaural rear channel signals are encoded.

While the Dolby Pro Logic is activated for this type of Dolby Digital source, the Ù DIGITAL indicator goes off.

Notes:

No test tone comes out of the center speakers when “CENTER SPK” is set to “NONE” (see page 20).

No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 20).

If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.

43

Image 48
Contents RX-884RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-884RBK Table of Contents Using the DSP Modes Selecting Your Favorite SEA Mode Creating Your Own SEA ModeFront Panel Remote Control Parts Identification3 4 5 678 90 = Getting Started GeneralLocations Handling the receiverConnecting the FM and AM MW/LW Antennas Getting StartedFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the rear and center speakers Connecting the subwoofer speakerCase 1 When you connect only one set of front speakers Case 2 When you connect two sets of front speakersAbout the speaker impedance Use front speakers with 4 16 ohm impedanceConnecting Audio/Video Components Analog connectionsAudio Components Video Components Audio component connectionsConnecting the TV and/or DBS tuner Video component connectionsConnecting DVD player Connecting VCRsDigital connections Digital 1 coaxial ForConnecting the Power Cord To shut off the power completelyPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlFrom the remote control What are the following indicators?Basic Operations On the front panelAdjusting the Volume Basic OperationsPress one of the source selecting buttons directly Selecting different sources for picture and soundFrom the remote control only Listening only with headphonesOn the front panel only Attenuating the Input Signal Adjusting the Subwoofer Output LevelDisplay changes to show the current setting Keys are activated for sound adjustmentsBasic Settings Selecting the Input ModeSelecting the DBS tuner as the source Changing the Source NameBasic Settings Adjusting the Front Speaker Output BalanceSetting the Subwoofer Information Listening at Low Volume LoudnessDigital Input Digital in Terminal Setting Setting the Speakers for the DSP ModesFront, Center, and Rear Speaker Setting Press Setting repeatedly until Front SPK FrontCenter Delay Time Setting Rear Delay Time SettingCrossover Frequency Setting Low Frequency Effect Attenuator Setting Dynamic Range Compression SettingTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo erase a stored preset station To tune in a preset stationSelecting the FM Reception Mode Receiving Radio BroadcastsAssigning Names to Preset Stations Press Tuner PRESET, while a character you want isFlashing Character is flashing after you have assigned a nameUsing the RDS Radio Data System to Receive FM Stations What Information Can RDS Signals Provide?To show the RDS signals To search for a program using the PTY codes Searching for a Program by PTY CodesTo continue searching after the first stop To stop searching any time during the processPress PTY Search while listening to an FM StationOn the display while PTY Select is flashing Display gives you the PTY codes described to RightSwitching to a Broadcast Program of Your Choice Temporarily Receiver enters EON standby modeTraffic Announcement in your area NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goes offUsing the SEA Modes Selecting Your Favorite SEA ModeTo cancel the SEA mode Using the SEA Modes Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing the DSP Modes On the 3D-PHONIC modeOn the DAP mode On Surround modeUsing the DSP Modes Using the 3D-PHONIC ModesPress DSP Mode Turn Multi JOG until the mode 3D Action or 3DTo cancel the 3D-PHONIC mode As you turn it, the effect level changes as followsPress Surround Mode repeatedly until the mode 3D Action or 3D DIGITAL, 3D DRAMA, or 3D TheaterYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes To cancel the DAP mode Press Surround Mode repeatedly until the mode youAdjust the speaker output levels as follows Want appears on the displayUsing the Dolby Digital and Dolby Pro Logic Modes Press Surround Mode repeatedly until PRO LogicOr Dolby Digital appears on the display To cancel the Surround mode Press Test to start checking the speaker output balancePress Cntr Tone to select the center tone level you want Press Dolby Surround so that the lamp on the button Lights upTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode To cancel the Theater Surround mode Press Cntr Tone to select the center tone level you wantDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Using the On-Screen Menus When you select OSD, seeSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundAdjusting the Front Speaker Output Balance Also see Listening at Low Volume Loudness Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVUsing the On-Screen Menus Adjusting the Subwoofer Output Level Also seeFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionSelecting Your Favorite SEA Mode Also see For Dolby Surround Pro LogicFor Dolby Digital For Theater Surround and Digital Theater SurroundCreating Your Own SEA Mode Also see Basic SettingsPress SET to store the setting into the SEA Usermode Storing the Preset Stations Also see Operating the TunerAssigning Names to the Preset Stations Also see Character entry screen appearsTuner Control menu appears again Checking the RDS Information Also see RDS Information menu appearsCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingText Compu Link Remote Control System What is a CD Text?Displaying the Disc Information on the TV screen Disc Search Only for CD PlayerText Compu Link Remote Control System Showing the Disc Information on the TV ScreenSearching a Disc Only for the CD player Search a disc by its performerPress SET again Going back to the Performer Search screen Press ExitGoing back to the Disc Title Search screen Press Exit Search a disc by its genrePress on Screen Control %/ Þ to move to GENRE, then press Genre Search screen appearsUsing your own User Files User File screen appears on the TVGoing back to the User File screen Press Exit Entering the Disc Information For the CD Player with the disc memory functionTitle Input Performer screen appears on the TV To move to Shift , then press SETFor the MD recorder Enter the disc title, referring to steps 3 and 4 onEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components CD player-changer TurntableCassette deck MD recorderOperating JVC’s Audio/Video Components VCR1 the VCR connected to the VCR1 jacksREC DVD playerAdjusts the volume Sets the input mode either TV orTurns on or off the TV Operating Other Manufactures’ Components Following buttons can be used for operating the TV10, 0, 100++10 Operating Other Manufactures’ Components Starts playbackPauses Try to operate your VCR by pressing VCR1Manufacturers’ codes for TV MTC Manufacturers’ codes for Catv converters 000, 037, 081 Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM