JVC RX-884RBK manual Text Compu Link Remote Control System, Disc Search Only for CD Player

Page 61

TEXT COMPU LINK Remote Control System

The TEXT COMPU LINK remote control system has been newly developed to deal with the disc information recorded in the CD Text* and MDs. Using these information in the discs, you can operate the CD player or MD recorder equipped with the TEXT COMPU LINK remote control system through the receiver.

English

CONNECTIONS:

To use this remote control system, you need to connect the CD player and/or MD recorder you want to operate, following the procedures below.

1.If you have already plugged your CD player, MD recorder, and this receiver into the AC outlets, unplug their AC power cords first.

2.Connect your CD player, MD recorder, and this receiver as follows, through the COMPU LINK-3 (SYNCHRO) jacks and TEXT COMPU LINK jacks.

1)COMPU LINK-3 (SYNCHRO) jacks: Use the cables with the monaural mini- plugs (not supplied with this receiver)

COMPU LINK – 3

(SYNCHRO)

CD player

MD recorder

2)TEXT COMPU LINK jacks: Use the cables with the stereo mini-plugs (not

supplied with this receiver)

 

 

TEXT

CD player

COMPU LINK

MD recorder

 

1(MASTER UNIT)

 

2(SLAVE UNIT)

IMPORTANT:

Set the Master/Slave Selector on the rear to “1(MASTER UNIT).”

“2(SLAVE UNIT)” is just for the serviceman’s use. The TEXT COMPU LINK remote control system does not function with the selector set to “2(SLAVE UNIT).”

3.Connect your CD player, MD recorder and this receiver, using the cables with RCA pin plugs (see page 9) (and a digital cable if you want — see page 12).

4.Plug the AC power cords of these components above into the AC outlets.

5.When turning on these components for the first time, turn on the connected components first, then turn on this receiver.

FUNCTIONS:

This remote control system allows you to use the functions listed below.

Displaying the Disc Information on the TV screen

Disc information such as its performer and disc title (and track titles only when a CD Text is selected) is shown on the TV screen.

Disc Search: Only for CD Player

This remote control system can allow you to search discs by the performer, disc title, and music genre.

With this disc search, you can easily find the disc you want to play.

Additional Functions:

If your CD player has the User File function, you can select a disc from the groups.

*A “user file” is a group of the discs you make as you like on the CD player.

If your CD player has the disc memory function, you can input the performer, disc title, and music genre about these normal audio CDs on the TV screen.

*What is a CD Text?

In a CD Text, some information about the disc (its disc title, performer, composer, arranger, etc.) is recorded.

Notes:

If your audio component has two COMPU LINK-3 (SYNCHRO) jacks, you can use either one. If it has only one COMPU LINK-3 (SYNCHRO) jack, connect it so that it is the last item in the series of components. (For example, the CD player in the diagram to the left.)

If your audio component has two TEXT COMPU LINK jacks, you can use either one. If it has only one TEXT COMPU LINK jack, connect it so that it is the last item in the series of components. (For example, the CD player in the diagram to the left.)

Refer also to the manuals supplied with your CD player or MD recorder.

Note:

If you turn on the receiver before turning on the other components after connecting components, the TEXT COMPU LINK remote control system does not work correctly.

If this happens:

1.Turn off the all components including this receiver.

2.Turn on the connected components.

3.Turn on this receiver.

56

Image 61
Contents RX-884RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-884RBK Table of Contents Selecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the DSP ModesParts Identification Front Panel Remote Control3 4 5 678 90 = General Getting StartedLocations Handling the receiverGetting Started Connecting the FM and AM MW/LW AntennasFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the subwoofer speaker Connecting the rear and center speakersCase 2 When you connect two sets of front speakers Case 1 When you connect only one set of front speakersAbout the speaker impedance Use front speakers with 4 16 ohm impedanceAnalog connections Connecting Audio/Video ComponentsAudio Components Video Components Audio component connectionsVideo component connections Connecting the TV and/or DBS tunerConnecting VCRs Connecting DVD playerDigital 1 coaxial For Digital connectionsTo shut off the power completely Connecting the Power CordPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlWhat are the following indicators? From the remote controlBasic Operations On the front panelBasic Operations Adjusting the VolumePress one of the source selecting buttons directly Selecting different sources for picture and soundListening only with headphones From the remote control onlyOn the front panel only Adjusting the Subwoofer Output Level Attenuating the Input SignalDisplay changes to show the current setting Keys are activated for sound adjustmentsSelecting the Input Mode Basic SettingsSelecting the DBS tuner as the source Changing the Source NameAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Listening at Low Volume LoudnessSetting the Speakers for the DSP Modes Digital Input Digital in Terminal SettingFront, Center, and Rear Speaker Setting Press Setting repeatedly until Front SPK FrontRear Delay Time Setting Center Delay Time SettingCrossover Frequency Setting Dynamic Range Compression Setting Low Frequency Effect Attenuator SettingTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To erase a stored preset stationSelecting the FM Reception Mode Receiving Radio BroadcastsPress Tuner PRESET, while a character you want is Assigning Names to Preset StationsFlashing Character is flashing after you have assigned a nameWhat Information Can RDS Signals Provide? Using the RDS Radio Data System to Receive FM StationsTo show the RDS signals Searching for a Program by PTY Codes To search for a program using the PTY codesTo continue searching after the first stop To stop searching any time during the processStation Press PTY Search while listening to an FMOn the display while PTY Select is flashing Display gives you the PTY codes described to RightReceiver enters EON standby mode Switching to a Broadcast Program of Your Choice TemporarilyTraffic Announcement in your area NewsPress EON so that the program type TA/NEWS/INFO goes off To stop listening to the program selected by EONSelecting Your Favorite SEA Mode Using the SEA ModesTo cancel the SEA mode Creating Your Own SEA Mode Using the SEA ModesTo recall your own SEA adjustment To erase a stored adjustmentOn the 3D-PHONIC mode Using the DSP ModesOn the DAP mode On Surround modeUsing the 3D-PHONIC Modes Using the DSP ModesPress DSP Mode Turn Multi JOG until the mode 3D Action or 3DAs you turn it, the effect level changes as follows To cancel the 3D-PHONIC modeAction or 3D DIGITAL, 3D DRAMA, or 3D Theater Press Surround Mode repeatedly until the mode 3DYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes Press Surround Mode repeatedly until the mode you To cancel the DAP modeAdjust the speaker output levels as follows Want appears on the displayPress Surround Mode repeatedly until PRO Logic Using the Dolby Digital and Dolby Pro Logic ModesOr Dolby Digital appears on the display Press Test to start checking the speaker output balance To cancel the Surround modePress Cntr Tone to select the center tone level you want Lights up Press Dolby Surround so that the lamp on the buttonTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode Press Cntr Tone to select the center tone level you want To cancel the Theater Surround modeDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 When you select OSD, see Using the On-Screen MenusSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundListening at Low Volume Loudness Also see Adjusting the Front Speaker Output Balance Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVAdjusting the Subwoofer Output Level Also see Using the On-Screen MenusFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionFor Dolby Surround Pro Logic Selecting Your Favorite SEA Mode Also seeFor Dolby Digital For Theater Surround and Digital Theater SurroundBasic Settings Creating Your Own SEA Mode Also seePress SET to store the setting into the SEA Usermode Operating the Tuner Storing the Preset Stations Also seeCharacter entry screen appears Assigning Names to the Preset Stations Also seeTuner Control menu appears again RDS Information menu appears Checking the RDS Information Also seeRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingWhat is a CD Text? Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen Text Compu Link Remote Control SystemSearch a disc by its performer Searching a Disc Only for the CD playerPress SET again Going back to the Performer Search screen Press ExitSearch a disc by its genre Going back to the Disc Title Search screen Press ExitPress on Screen Control %/ Þ to move to GENRE, then press Genre Search screen appearsUser File screen appears on the TV Using your own User FilesGoing back to the User File screen Press Exit For the CD Player with the disc memory function Entering the Disc InformationTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the disc title, referring to steps 3 and 4 on For the MD recorderEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Turntable CD player-changerCassette deck MD recorderVCR1 the VCR connected to the VCR1 jacks Operating JVC’s Audio/Video ComponentsREC DVD playerSets the input mode either TV or Adjusts the volumeTurns on or off the TV Following buttons can be used for operating the TV Operating Other Manufactures’ Components10, 0, 100++10 Starts playback Operating Other Manufactures’ ComponentsPauses Try to operate your VCR by pressing VCR1Manufacturers’ codes for TV MTC Manufacturers’ codes for Catv converters 000, 037, 081 Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM