JVC RX-7010RBK, RX-7012RSL manual Basic Settings, Recording a Source, Changing the Source Name

Page 16
TV SOUND/DBS
SOURCE NAME
TAPE/CDR
SOURCE NAME

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.

Recording a Source

For analog-to-analog recording

You can record any analog source through the receiver to —

•the cassette deck (or CD recorder) connected to the TAPE/CDR jacks, and

•the VCR connected to the VCR jacks

— at the same time.

Changing the Source Name

When you have connected a CD recorder to the TAPE/CDR jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the CD recorder or DBS tuner as the source.

On the front panel ONLY:

For digital-to-digital recording

You can record the currently selected digital input through the receiver to a digital recording device connected to the DIGITAL OUT terminal.

Notes:

•Analog-to-digital and digital-to-analog recordings are not possible.

•The output volume level, bass boost (see page 12), tone adjustment (see page 12), and DSP modes (see page 23) cannot affect the recording.

•The test tone signal (see pages 26 and 27) does not come out through the DIGITAL OUT terminal.

When changing the source name from “TAPE” to “CDR”:

• Press and hold TAPE/CDR/ SOURCE NAME to assign “CDR.”

When changing the source name from “TV SOUND” to “DBS”:

• Press and hold TV SOUND/DBS/ SOURCE NAME to assign “DBS.”

Adjusting the Front Speaker Output

Balance

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.

Before you start, remember....

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press ADJUST repeatedly until

ADJUST SETTING

“L/R BALANCE” appears on the

 

display.

 

To change the source name to “TAPE” or “TV SOUND,” repeat

the same procedure above — press and hold TAPE/CDR/SOURCE NAME to select “TAPE” or TV SOUND/DBS/SOURCE NAME to select “TV SOUND.”

Note:

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

–“TAPE” or “TV SOUND” will appear on the display when you select the CD recorder or DBS tuner.

–You cannot use the digital input (see page 16) for the CD recorder.

–You cannot use the COMPU LINK remote control system (see page 31) to operate the CD recorder.

The display changes to show the current setting.

2.Press CONTROL UP 5/DOWN ° to adjust the balance.

•Pressing CONTROL UP 5 decreases the left channel output from CNTR (Center) to –21.

•Pressing CONTROL DOWN °decreases the right channel output from CNTR (Center) to –21.

CONTROL

DOWN UP

13

Page 15 Page 17
Image 16
Page 15 Page 17
Contents RX-7010RBK / RX-7012RSL If in Doubt Consult a Competent Electrician RX-7010RBK RX-7012RSL Table of Contents Ex. When you press CD button Remote Control Front PanelParts Identification Before Installation Checking the Supplied AccessoriesConnecting the FM and AM MW/LW Antennas Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers AM MW/LW Antenna ConnectionsConnecting Audio/Video Components Connecting the subwoofer speakerConnecting the rear and center speakers About the speaker impedanceCD player Video component connectionsCassette deck or CD recorder If your audio components have a Compu Link jackTV and/or DBS tuner To audioDBS tuner DVD playerDigital input terminals Digital connectionsDigital output terminal Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet R6PSUM-3/AA15FBasic Operations Turning the Power On and Off StandbySelecting the Source to Play Adjusting the Volume Selecting the Front Speakers Listening only with headphonesHeadphone mode Selecting different sources for picture and soundAttenuating the Input Signal Adjusting the ToneAdjusting the Subwoofer Output Level Muting the SoundBasic Settings Adjusting the Front Speaker Output BalanceRecording a Source Changing the Source NameSetting the Subwoofer Information Setting the Speakers for the DSP ModesTo select the delay time of the rear speaker output LFE ATT Low Frequency Effect Attenuator appears on DisplayCrossover FRQ Crossover Frequency appears on the display Press Control UP 5/DOWNDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode Using the RDS Radio Data System to Receive FM Stations Searching for a Program by PTY CodesSwitching to a Broadcast Program Your Choice Temporarily If the FM station you are listening to is You have selectedTo stop listening to the program selected by EON What are the DSP Modes? Using the DSP ModesSurround modes DVD Multi Playback Mode Available DSP modes according to the input modeReproducing the Sound Field DAP modesAvailable DSP modes Available DSP Modes According to the Speaker ArrangementBy pressing Surround on By pressing DSP MODE, Adjusting the Surround Modes Press DSP Mode repeatedly until Adjust the effect levelPress Effect to select an effect Level you wantAdjusting the DAP Modes To cancel the Dolby/DTS Surround mode To cancel the DSP modeActivating the DSP Modes Press Surround ON/OFFUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverCD player Cassette deck CD recorder Synchronized RecordingOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD changer TurntableCassette deck REWOperating Video Components DVD playerOperating Other Manufacturers’ Video Equipment For Catv converter Release CATV/DBSFor DBS tuner Release VCR If there are more than one code listed for your brandTry to operate your VCR by pressing VCR Release Audio JVC Denon Panasonic Philips Pioneer04, 05 RCA Samsung Sony Toshiba YamahaTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF AM MW/LW tuner0301NHMMDWJEIN

RX-7012RSL, RX-7010RBK specifications

JVC has long been a respected name in the audio and video industries, and the RX-7012RSL and RX-7010RBK home theater receivers stand as testaments to the brand’s commitment to high-quality sound and advanced technology. These models are designed to enhance any home theater experience, thanks to their robust feature sets and impressive performance.

The RX-7012RSL offers a powerful 100 watts per channel, making it ideal for even the largest living rooms or media spaces. With a total of five channels, this receiver can seamlessly drive a full surround sound setup, allowing users to immerse themselves in their favorite movies and music. The RX-7010RBK, while slightly lower in power, still delivers exceptional quality at 80 watts per channel, providing ample output for most home theaters.

Both models are equipped with JVC’s proprietary Digital Sound Processing technology, which enhances audio quality by optimizing bass and treble levels, ensuring crystal-clear sound reproduction across all frequencies. This feature is particularly useful for home theater enthusiasts who desire a theater-like experience in the comfort of their living room.

For connectivity, the RX-7012RSL and RX-7010RBK are outfitted with a variety of inputs, including HDMI, optical, and coaxial options. This versatility allows users to connect multiple devices, such as Blu-ray players, gaming consoles, and streaming devices, all while maintaining high-definition audio and video quality. Additionally, both receivers support Dolby Digital and DTS surround sound formats, enabling an immersive listening experience.

In terms of design, these JVC receivers sport a sleek, modern look with an easy-to-read display and intuitive controls. The remote control is user-friendly, giving users quick access to functions like volume control, sound settings, and inputs.

One notable feature of both the RX-7012RSL and RX-7010RBK is their zone control capabilities. This allows users to create separate audio zones in their home, enabling different rooms to enjoy unique audio settings and sources simultaneously.

In summary, the JVC RX-7012RSL and RX-7010RBK home theater receivers combine power, advanced technology, and user-friendly design to deliver exceptional audio performance. With their robust connectivity options and sound processing capabilities, these models are perfect choices for anyone looking to elevate their home entertainment experience.
Top Page Image Contents