JVC RX-7010RBK, RX-7012RSL manual Using the DSP Modes, What are the DSP Modes?, Surround modes

Page 26
DOLBY SURROUND
D I G I T A L
DOLBY SURROUND

Using the DSP Modes

The built-in Surround Processor provides two types of the DSP (Digital Signal Processor) mode — Surround mode and DAP (Digital Acoustic Processor) mode.

What are the DSP Modes?

Surround modes

With this receiver, you can use three types of the Surround mode.

Following modes cannot be used when only the front speakers are connected to this receiver (without the rear speakers or center speaker).

Dolby Surround (Dolby Digital and Dolby Pro Logic)*

Used to watch the soundtracks of software encoded with Dolby

Digital (bearing the mark ) or with Dolby Surround

(bearing the mark ).

Dolby Surround encoding format records the left front channel, right front channel, center channel, and rear channel (total 4 channels) signals into 2 channels. The Dolby Pro Logic decoder built in this receiver decodes these 2 channel signals into original 4 channel signals — matrix-based multichannel reproduction, and allows you to enjoy the realistic stereo sounds in your listening room.

On the other hand, Dolby Digital encoding method (so called discrete 5.1 channel digital audio format) records and compresses the left front channel, right front channel, center channel, left rear channel, right rear channel, and LFE channel (total 6 channels, but LFE channel is counted as 0.1 channel, therefore called 5.1 channels) signals digitally. Each channel is completely independent from other channel signals to avoid interference, therefore, you can obtain much better sound quality with much stereo and surround effects.

The Dolby Digital decoder built in this receiver can create much more realistic sound field in your listening room. You may feel as if you were in a real theater.

In addition, Dolby Digital enables stereo rear sounds, and sets the cutoff frequency of the rear treble at 20 kHz, compared to 7 kHz for Dolby Pro Logic. These facts enhance the sound movement and being-there feelings much more than Dolby Pro Logic.

•To enjoy the software encoded with Dolby Digital, you must connect the source component using the digital terminal on the rear of this receiver. (See page 8.)

DTS Digital Surround**

DTS Digital Surround is another discrete 5.1 channel digital audio format available on CD, LD, and DVD software.

Compared to Dolby Digital, audio compression rate is relatively low. This fact allows DTS Digital Surround format to add breadth and depth to the reproduced sounds. As a result, DTS Digital Surround features natural, solid and clear sound.

•To enjoy the software encoded with DTS Digital Surround, you must connect the source component using the digital terminal on the rear of this receiver. (See page 8.)

JVC Theater Surround

In order to reproduce a more realistic sound field in your listening room while playing soundtracks of software encoded with Dolby

Surround (bearing the mark ), you can use JVC Theater Surround.

Notes:

•The DSP modes have no effect on monaural sources.

•When you select “DVD MULTI” as the source to play, you cannot select or adjust the DSP modes.

•The PRO LOGIC indicator lights up when the Dolby Pro Logic decoder built in this receiver is activated.

*Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992–1997 Dolby Laboratories, Inc. All rights reserved.

**Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issues and pending. “DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc. ©1996 Digital Theater Systems, Inc. All rights reserved.

23

Page 25 Page 27
Image 26
Page 25 Page 27
Contents RX-7010RBK / RX-7012RSL If in Doubt Consult a Competent Electrician RX-7010RBK RX-7012RSL Table of Contents Parts Identification Remote Control Front PanelEx. When you press CD button Connecting the FM and AM MW/LW Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM MW/LW Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceCassette deck or CD recorder CD playerVideo component connections If your audio components have a Compu Link jackDBS tuner TV and/or DBS tunerTo audio DVD playerDigital output terminal Digital connectionsDigital input terminals Plug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control R6PSUM-3/AA15FSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Headphone mode Adjusting the Volume Selecting the Front SpeakersListening only with headphones Selecting different sources for picture and soundAdjusting the Subwoofer Output Level Attenuating the Input SignalAdjusting the Tone Muting the SoundRecording a Source Basic SettingsAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Subwoofer Information Setting the Speakers for the DSP ModesCrossover FRQ Crossover Frequency appears on the display To select the delay time of the rear speaker outputLFE ATT Low Frequency Effect Attenuator appears on Display Press Control UP 5/DOWNDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Using the RDS Radio Data System to Receive FM Stations Searching for a Program by PTY CodesSwitching to a Broadcast Program Your Choice Temporarily To stop listening to the program selected by EON You have selectedIf the FM station you are listening to is Surround modes Using the DSP ModesWhat are the DSP Modes? Reproducing the Sound Field DVD Multi Playback ModeAvailable DSP modes according to the input mode DAP modesBy pressing Surround on By pressing DSP MODE, Available DSP Modes According to the Speaker ArrangementAvailable DSP modes Adjusting the Surround Modes Press Effect to select an effect Press DSP Mode repeatedly untilAdjust the effect level Level you wantAdjusting the DAP Modes Activating the DSP Modes To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Press Surround ON/OFFPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displayCD player Cassette deck CD recorder Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck CD changerTurntable REWOperating Video Components DVD playerOperating Other Manufacturers’ Video Equipment For DBS tuner Release CATV/DBSFor Catv converter Try to operate your VCR by pressing VCR If there are more than one code listed for your brandRelease VCR 04, 05 Release AudioJVC Denon Panasonic Philips Pioneer RCA Samsung Sony Toshiba YamahaTroubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM MW/LW tuner0301NHMMDWJEIN

RX-7012RSL, RX-7010RBK specifications

JVC has long been a respected name in the audio and video industries, and the RX-7012RSL and RX-7010RBK home theater receivers stand as testaments to the brand’s commitment to high-quality sound and advanced technology. These models are designed to enhance any home theater experience, thanks to their robust feature sets and impressive performance.

The RX-7012RSL offers a powerful 100 watts per channel, making it ideal for even the largest living rooms or media spaces. With a total of five channels, this receiver can seamlessly drive a full surround sound setup, allowing users to immerse themselves in their favorite movies and music. The RX-7010RBK, while slightly lower in power, still delivers exceptional quality at 80 watts per channel, providing ample output for most home theaters.

Both models are equipped with JVC’s proprietary Digital Sound Processing technology, which enhances audio quality by optimizing bass and treble levels, ensuring crystal-clear sound reproduction across all frequencies. This feature is particularly useful for home theater enthusiasts who desire a theater-like experience in the comfort of their living room.

For connectivity, the RX-7012RSL and RX-7010RBK are outfitted with a variety of inputs, including HDMI, optical, and coaxial options. This versatility allows users to connect multiple devices, such as Blu-ray players, gaming consoles, and streaming devices, all while maintaining high-definition audio and video quality. Additionally, both receivers support Dolby Digital and DTS surround sound formats, enabling an immersive listening experience.

In terms of design, these JVC receivers sport a sleek, modern look with an easy-to-read display and intuitive controls. The remote control is user-friendly, giving users quick access to functions like volume control, sound settings, and inputs.

One notable feature of both the RX-7012RSL and RX-7010RBK is their zone control capabilities. This allows users to create separate audio zones in their home, enabling different rooms to enjoy unique audio settings and sources simultaneously.

In summary, the JVC RX-7012RSL and RX-7010RBK home theater receivers combine power, advanced technology, and user-friendly design to deliver exceptional audio performance. With their robust connectivity options and sound processing capabilities, these models are perfect choices for anyone looking to elevate their home entertainment experience.
Top Page Image Contents