JVC RX-D205S Troubleshooting, Power, Problem Possible Cause Solution, Sound, Remote control Tuner

Page 41

Troubleshooting

Use this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC’s service center.

Power

PROBLEM

POSSIBLE CAUSE

 

SOLUTION

The power does not come on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

 

The receiver turns off (enters standby

Speakers are overloaded because of high

1.

Stop the playback source.

mode).

volume.

2.

Turn on the receiver again, then turn the

 

 

 

volume down.

 

 

 

 

Speakers are overloaded because of a

Check the speaker wiring. If speaker wiring

 

short circuit at the speaker terminals.

is not short-circuited, contact your dealer.

 

 

 

 

The receiver is overloaded because of a

Consult your dealer after unplugging the

 

high voltage.

power cord.

 

 

 

“OVER HEAT” flashes on the display,

The receiver is overloaded because of high

Turn the volume down or turn off the

then the receiver turns off.

volume or long time usage.

receiver for a while and turn it on again.

 

 

If the receiver turns off soon after doing

 

 

solutions above, consult your dealer after

 

 

unplugging the power cord.

Sound

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring, then reconnect if

 

 

necessary (see page 6) after unplugging

 

 

the power cord.

 

 

 

 

Connections are incorrect.

Check the audio connections (see pages 7

 

 

to 11) after unplugging the power cord.

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute (see

 

 

page 14).

 

 

 

 

An incorrect input mode (analog or digital)

Select the correct input mode (analog or

 

is selected.

digital).

 

 

 

Sound from one speaker only.

Speaker signal cables are not connected

Check speaker wiring and reconnect if

 

properly.

necessary (see page 6) after unplugging

 

 

the power cord.

 

 

 

Sounds are intermittently distorted by

When you use the digital coaxial connection,

This is not a malfunction.

the outside noise such as a lightning

the sounds may be intermittently distorted

 

discharge.

by the outside noise such as a lightning

 

 

discharge but the sound will be restored

 

 

automatically.

 

Remote control

Tuner

Remote control does not operate as

The remote control is not ready for your

Set the mode selector correctly, then press

you intend.

intended operation.

the corresponding source selecting button

 

 

or SOUND before operation.

 

 

 

Remote control does not work.

There is an obstruction blocking the remote

Remove the obstruction.

 

sensor on the receiver.

 

 

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

 

The mode selector is set to the incorrect

Set the mode selector to the proper

 

position.

position.

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

reception.

 

your dealer.

 

 

 

 

The station is too far away.

Select another station.

 

 

 

 

The wrong antenna is being used.

Check with your dealer to be sure you have

 

 

the correct antenna.

 

 

 

 

Antennas are not connected properly.

Check the connections.

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

traffic.

39

Image 41
Contents For Customer Use RX-D205S / RX-D206BDeclaration of Conformity For Canada/pour Le CanadaTable of Contents Parts identification Remote controlFront panel Display windowPutting batteries in the remote control Before InstallationChecking the supplied accessories Getting startedFM antenna connection Connecting the FM and AM antennasAM antenna connection Speaker Layout Diagram Connecting the speakersConnecting the speakers Connecting the powered subwooferIf your video components have AV Compu Link terminal Connecting video components‰ Ï Ì Connecting a DBS tuner Connect the unit to the PC using a USB cable not supplied How to install the USB driversUSB connection Digital connectionUSB drivers are installed automatically Connecting the power cordCheck if the drivers are correctly installed Now the PC is ready for playback through the USB connectionSelecting the analog or digital input mode Turn on the powerTo turn off the power into standby Basic operationsListening with headphones Adjust the volumeInitial setting Digital Auto Ex. When Dolby Digital is selectedBasic adjustment of auto memory Turning off the power with the Sleep TimerSignal and speaker indicators on the display Turning off the sounds temporarilyPress Setting Basic settingsPress SET Before you start, rememberSpeakers channels number and the size Basic setting itemsSetting subwoofer information-SUBWOOFER Setting the speakersSetting the surround back speakers-S Back OUT Turn Multi JOG to select the appropriate SettingSetting the speaker distance Activating the EX/ES/PLIIx setting- EX/ES/PLIIxFrom the remote control AutoSetting subwoofer output-SUBWOOFER OUT Setting bass soundSetting the crossover frequency-CROSSOVER Setting the low frequency effect attenuator-LFEVCR S/C Using the Midnight modeDVD S/C Basic adjustment items Sound adjustmentsOperating procedure Press AdjustPress Test again to stop the test tone Press SoundAttenuating the input signal-INPUT ATT Adjusting the bass soundsAdjusting the virtual room size for DSP modes Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone Using preset tuning Tuning in to stations manuallyTo store the preset stations Tuner operationsTo tune in a preset station Selecting the FM reception modeReproducing theater ambience Creating realistic sound fieldsIntroducing the Surround modes Dolby DigitalDTS 3D Headphone modeAbout other digital signals Digital Acoustic Processor DAP modes All Channel Stereo mode ALL CH StereoIntroducing the DSP modes About the DSP modes Using the Surround/DSP modesVirtual Surround Back DTSSelecting the Surround/DSP modes When you select Auto SurroundConnections 2 Video cable connection AV Compu Link remote control systemConnections 1 AV Compu Link connection Automatic selection of TV’s input mode Connecting procedureAutomatic power on/off One-touch video playOperating other JVC products Release STANDBY/ON DVR/DVD DVD recorder or DVD playerDVR/DVD MenuOperating other manufacturers’ products Changing the transmittable signals for operating a TVRelease STANDBY/ON TV/DBS/CATV Manufacturers’ codes for TVRelease STANDBY/ON VCR Changing the transmittable signals for operating a VCRTry to operate your VCR by pressing Manufacturers’ codes for VCRManufacturers’ codes for DVD player Manufacturers’ codes for Catv converter/ DBS tunerTry to operate your DVD player by pressing Power TroubleshootingProblem Possible Cause Solution Remote control TunerAmplifier SpecificationsFM tuner IHF AM tunerPage Page Audio Video Control Receiver RX-D206B Mises en garde, précautions et indications diverses English Parts identification Source Master Getting started Connecting the FM and AM antennas Connecting the speakers Connecting video components ‰ Ï Ì To left/right audio channel output USB connection Connecting the power cord Basic operations Adjust the volume Turning off the sounds temporarily 0ch 2.1ch 3.0ch 3.1ch 0ch 4.1ch 5.0ch 5.1ch SUBWOOFER*1 Quick SPK SETFront SPK*1 Center SPK*1Setting the surround back speakers-S Back OUT Activating the EX/ES/PLIIx setting- EX/ES/PLIIx Surround Setting Midnight Mode Sound adjustments Adjusting the speaker output levels Adjusting the bass sounds Width Tuner operations Selecting the FM reception mode Creating realistic sound fields DTS Introducing the DSP modes Digital Auto Surround is the initial setting Video cable Source RX-D206B Equipment To video input Connecting procedure Operating other JVC products DVD recorder or DVD player Operating other manufacturers’ products 01, 02 Emerson Gold Star Hitachi Mitsubishi STANDBY/ON TV/DBS/CATV Sound Specifications RX-D206B
Related manuals
Manual 45 pages 60.21 Kb

RX-D205S, RX-D206B specifications

The JVC RX-D205S and RX-D206B are two versatile and feature-rich audio receivers designed to deliver high-quality sound experiences for home entertainment enthusiasts. Both models are part of JVC's commitment to providing advanced audio technologies while ensuring user-friendly functionality and connectivity options.

One of the standout features of the RX-D205S and RX-D206B is their multi-channel surround sound capability. Each receiver supports a range of audio formats, including Dolby Digital and DTS, allowing users to enjoy immersive audio experiences whether they're watching movies, playing video games, or listening to music. With built-in amplification, these models deliver powerful audio performance, making them ideal for both small and large rooms.

Connectivity is a significant highlight for both models. They come equipped with a variety of input options, including multiple HDMI ports, optical and coaxial inputs, and analog inputs. This extensive connectivity ensures compatibility with a wide range of devices such as Blu-ray players, gaming consoles, streaming devices, and more. Additionally, the receivers support 4K Ultra HD passthrough, ensuring that users can enjoy high-resolution video content without compromising on audio quality.

Another key feature is their user-friendly interface and remote control, allowing users to navigate settings, adjust volume levels, and switch between input sources effortlessly. Both models also incorporate Bluetooth technology, enabling wireless streaming from smartphones and tablets. This feature enhances convenience, allowing users to easily enjoy their favorite playlists or podcasts directly from their mobile devices.

In terms of design, the RX-D205S and RX-D206B boast a sleek and modern aesthetic, making them fitting additions to any home entertainment setup. They are designed for durability and longevity, with high-quality components that contribute to their excellent sound performance.

In summary, the JVC RX-D205S and RX-D206B are impressive audio receivers that combine innovative technologies with practical features. Their multi-channel support, versatile connectivity options, Bluetooth capability, and robust design make them excellent choices for anyone seeking to upgrade their home audio system and enjoy an elevated entertainment experience. Whether for casual listening or cinematic immersion, these receivers deliver powerful performance and ease of use, establishing them as noteworthy contenders in the world of home audio.