JVC RX-D206B, RX-D205S manual Setting the surround back speakers-S Back OUT

Press SETTING.

The source indication resumes on the display.

7

Your setting is stored.

5 Press SET.

6 Repeat steps 2 to 5 to set other items if necessary.

Operating procedure

1,7 3,5 2,4

On the front panel ONLY:

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Ex.: When setting DIGITAL IN 1 terminal.

1Press SETTING.

MULTI JOG now works for the setting operation.

2Turn MULTI JOG until the item you want to set appears on the display.

•As you turn MULTI JOG, the setting items change as follows:

ANALOG

LR

S.WFR

QUICK SPK SET	SUBWOOFER
FRONT SPK	CENTER SPK
SURROUND SPK	S BACK SPK
S BACK OUT	DIST UNIT
FRONT L DIST	FRONT R DIST
CENTER DIST	SURR L DIST
SURR R DIST	S BACK DIST
S BACK L DIST	S BACK R DIST
EX/ES/PLIIx	DUAL MONO
SUBWOOFER OUT	CROSSOVER
LFE ATT	MIDNIGHT MODE
DIGITAL IN 1	DIGITAL IN 2
DIGITAL IN 3	DVD VIDEO IN
VCR VIDEO IN	DBS VIDEO IN
(Back to the beginning)

3Press SET.

The current setting of the selected item appears.

ANALOG

LR

S.WFR

4Turn MULTI JOG to select the appropriate

setting.

ANALOG

LR

S.WFR

DVR/DVD DBS

TVVCR

Setting the speakers

To obtain the best possible surround effect from the Surround and DSP modes, register the setting about the speaker after all connections are completed.

•If you have used Quick Speaker Setup on page 15, this setting is not required.

•You cannot use the remote control for this setting.

Setting subwoofer information—SUBWOOFER

Select whether you have connected a subwoofer or not.

SUBWFR <YES> Select when you have connected a

subwoofer.

The subwoofer indicator ( S.WFR ) lights up on the display. You can adjust the subwoofer output level (see page 22).

SUBWFR <NO> Select when you have disconnected a subwoofer. Selecting this changes the front speaker size to “LRG” (see below).

Initial setting: SUBWFR <NO>

Setting the speaker size—FRONT SPK (front speakers), CENTER SPK (center speaker), SURROUND SPK (surround speakers), S BACK SPK (surround back speakers)

Register the sizes of all the connected speakers.

<LRG> (large)		Select when the cone speaker size is
		larger than 12 cm.
	<SML> (small)	Select when the cone speaker size is
		smaller than 12 cm.
	<NO>	Select when you have disconnected a
		speaker. (Not selectable for the front
		speakers.)

Initial setting: <LRG> (for the front speakers) <SML> (for other speakers)

Setting the surround back speaker(s)—S BACK OUT

Register the number of surround back speaker(s).

SB OUT <1SPK> Select when you use one surround back speaker.

SB OUT <2SPK> Select when you use two surround back speakers.

Initial setting: SB OUT <2SPK>

NOTES

•If you have selected “SML (small)” for the front speaker size, you cannot select “LRG (large)” for other speakers.

•When “SUBWOOFER” is set to “SUBWFR <NO>,” the front speaker size is fixed to “LRG” (and you cannot select “SML”).

•When “SURROUND SPK” is set to “SML (small),” you cannot select “LRG (large)” for the surround back speaker.

•When “SURROUND SPK” is set to “NO,” the surround back speaker is fixed to “NO.”

•When “S BACK SPK” is set to “NO,” you cannot select “S BACK OUT.”

•When “SB OUT” is set to “<1SPK>,” connect the surround back speaker to the left surround back speaker terminal (see page 6). No sound comes from the surround back speaker if you connect it to the right surround back speaker terminal.

English

17