JVC RX-D205S, RX-D206B manual Adjusting the speaker output levels

English

Adjusting the speaker output levels

•SUBWFR LVL (subwoofer output level),

•FRONT L LVL (left front speaker output level),

•FRONT R LVL (right front speaker output level),

•CENTER LVL (center speaker output level),

•SURR L LVL (left surround speaker output level),

•SURR R LVL (right surround speaker output level),

•S BACK L LVL (left surround back speaker output level),

•S BACK R LVL (right surround back speaker output level)

You can adjust the speaker output levels.

Adjust all the speakers’ output levels so that you can listen to the sounds from all the speakers at the same level.

•Once you have made an adjustment, it is memorized for each source.

Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)

Initial setting: 0 (dB) for all speakers

NOTES

•	If you have selected “NO” for a speaker (see page 17), the
	output level for the corresponding speaker is not adjustable.
•	If you have selected “<1SPK>” for “S BACK OUT” (see page
	17), “S BACK LVL” appears instead of “S BACK L LVL” and “S
	BACK R LVL.”

Adjusting the equalization patterns— D EQ 63Hz/250Hz/1kHz/4kHz/16kHz

You can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers.

•Once you have made an adjustment, it is memorized for each source.

Adjustable range: –8 (dB) to +8 (dB) (in 2 dB intervals)

Initial setting: 0 (dB) for all bands

•When adjustment is made, the DIGITAL EQ indicator lights up on the display.

If no adjustment is required, set all the frequency bands to “0 (dB).”

• The DIGITAL EQ indicator goes off from the display.

From the remote control:

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

• While using the headphones, you can adjust only the left and

right front speakers’ output level.

From the remote control:

1Press SOUND.

2Press TEST to check the speakers’ output balance.

“TEST FL” starts flashing on the display, and a test tone comes out of the speakers clockwise.

1Press SOUND.

2Press D. EQ FREQ repeatedly to select the band you want to adjust.

3Press LEVEL9 or LEVEL( to adjust the equalization pattern of the selected band.

4Repeat steps 2 and 3 to adjust other bands.

1 2 3

4 5 6

7 8 9

10 0 10

2

3

1

			2,4
1	2	3
4	5	6	3
7	8	9
10	0	10

1

•You can adjust the speaker output levels without the test tone.

3Adjust the speaker output levels.

Press the numeric button corresponding to the speaker you want to adjust, then LEVEL9 or LEVEL( to adjust the output level.

Ex.: To adjust the output level for the left front speaker (L), press FRONT L, then LEVEL9 or LEVEL(.

4Press TEST again to stop the test tone.

NOTES

•No test tone comes out of the speakers for which the speaker setting is set to “NO” (see page 17).

•No test tone is available when the headphone is in use.

•If you have selected “<1SPK>” for “S BACK OUT” (see page 17), press S BACK L, then LEVEL9 or LEVEL( to adjust the output level.

•After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation.

NOTE

After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation.

22