Weider 831.153932 user manual 119 100 118

Page 12

19.Route the Swivel High Cable (74) through the Swivel Upright (5) and over a 115mm Pulley (119). Attach the Pulley inside the Upright with an M10 x 65mm Bolt (59), two M10 Washers (91), two 12.5 Spacers (89), and an M10 Nylon Locknut (87).

Attach an M10 x 65mm Bolt (59), two M10 Washers (91), and an M10 Nylon Locknut (87) to the Swivel Upright (5).

20.Remove the preattached 90mm Pulleys (78) from the Small Pulley Plates (31).

Wrap the Swivel High Cable (74) over a 90mm Pulley (78). Attach the Pulley and a Cable Trap (68) to the second set of holes from the top of the Small Pulley Plates (31) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the

Cable Trap is turned to hold the Cable in the groove of the Pulley.

21.Wrap the Swivel High Cable (74) over a 115mm Pulley (119). Attach the Pulley inside of the indicat- ed bracket on the Top Frame (6) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87).

22.Lift the Weight Tube (43) and the Top Weight (45) closest to the Swivel Upright (5). Make sure that the small pin on the Weight Tube is inside of the groove under the Top Weight.

Insert a Weight Pin (50) into the stack of Weights (44). Place a 50mm Washer (1) on top of the Weight Tube (43). Thread an M12 Nut (118) halfway onto the end of the Swivel High Cable (74). Screw the end of the Cable two full turns into the Weight Tube. Then, tighten the Nut against the 50mm Washer.

23.Locate the Swivel Cable (17), which is 2930mm long and has an eyelet on each end. Attach the Cable inside the Top Frame (6) with an M10 x 65mm Bolt (59), two M10 Washers (91), and an M10 Nylon Locknut (87).

12

19

 

 

91

59

 

 

5

 

 

 

 

 

59

 

 

 

 

 

 

91

 

 

 

 

91

87

 

 

 

 

 

 

 

 

 

89

 

 

 

 

 

91

 

 

 

 

 

 

87

89

 

119

 

 

74

 

 

 

 

 

 

20

 

 

 

 

 

 

 

 

 

74

 

 

 

 

 

 

87

 

 

 

 

 

 

 

 

 

100

 

 

 

78

68

31

 

 

 

31

 

 

 

21

 

 

 

 

 

 

 

 

 

 

 

 

6

 

93

 

 

 

 

 

 

 

 

 

 

 

87

 

 

 

119

74

22

 

 

 

 

 

 

 

 

 

 

 

 

74

5

 

 

 

 

 

118

 

 

 

 

 

 

50

 

 

45

 

 

1

 

 

 

 

 

 

 

 

 

 

43

 

 

 

 

 

 

 

 

 

 

 

 

44

23

 

 

59

 

 

 

 

 

 

 

 

87

 

 

 

91

 

 

 

 

 

 

17

 

 

 

 

 

6

Image 12
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions DecalBefore YOU Begin DecalOne on each side Assembly Frame Assembly Locknut the Squat Knee Rest must be able to pivotDo not tighten the Locknuts yet Locknuts yet Assemble the other weight stack in the same way Open the parts bag labeled ARM Assembly Tighten all of the M10 Nylon Locknuts 87 used in stepsButterfly Frame must be able to pivot easily Cable Assembly 119 100 118 100 102 121 Trap is turned to hold the Cable in the groove of the Pulley Page Cable is in the groove of the Pulley Trap is turned to hold the Cable in the groove of the Pulley Trap is turned to hold the Cable in the groove of the Pulley Seat Assembly Locate and open the parts bag labeled Seat AssemblyRepeat this step with the other end of the Squat Arm Nylon Locknuts yetTighten all of the M10 Nylon Locknuts 87 used in this step Page Adjustments Changing the Weight SettingConverting the Butterfly Arms Ing any exerciseAdjusting the Squat ARM or Swivel Carriage Adjusting the Squat Knee RestAttaching the Curl PAD Weight Resistance Chart StationLbs Top Troubleshooting Tightening the CablesCable Diagrams Lat CableButterfly Cable Swivel High Cable Squat Cable Leg Lever Swivel CableSwivel Low Part Identification CHART-Model No R0404APage Page Part LIST-Model No Key Qty DescriptionExploded DRAWING-Model No Full 90 DAY Warranty Sears, Roebuck and Co., Dept WA, Hoffman Estates, IL