Weider 9940 user manual Remove a Pro Pulley 26 from the bag labeled Pulley BAG

Page 15

31.Remove a Pro Pulley (26) from the bag labeled “PULLEY BAG 2.

Identify the Low Pulley Cable (75). It is approximately 143 1/2” long and it has a ball on one end and a loop on the other. Route the end with the loop through the slot in the cable guide on the Butterfly Base (4).

Route the Low Pulley Cable (75) under a Pro Pulley (26) as shown. Attach the Pro Pulley and a Cable Trap (25) to the bracket on the Butterfly Base (4) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).

Make sure the Cable Trap is oriented as shown.

32.Wrap the Low Pulley Cable (75) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley and a Cable Trap (25) to the indicated hole in the Butterfly Upright (1) with a 3/8” x 4 3/4” Bolt (60) and a 3/8” Nylon Jamnut (63). Note: Thread the Jamnut only two turns onto the Bolt, since you will later attach another Pulley to the Bolt. Make sure the Cable Trap is oriented as shown.

33.Wrap the Low Pulley Cable (75) over a 3 1/2” Pulley

(24)in the direction shown. Attach the Pulley and a Cable Trap (25) to the lower hole in the Adjustable Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50). Make sure the Cable Trap is oriented as shown.

34.Remove the 3/8” Nylon Jamnut (63) from the 3/8” x 4 3/4” Bolt (60) inserted into the Butterfly Upright (1) in step 32.

Wrap the Low Pulley Cable (75) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60) with the 3/8” Nylon Jamnut (63). Make sure the

Cable Trap is oriented as shown.

31

 

 

54

26

 

 

 

 

25

 

Cable

 

4

 

 

Guide

 

 

 

75

50

 

 

32

60

 

 

 

1

 

24

 

 

25

 

 

 

63

 

75

 

33

 

 

 

 

23

 

 

50

 

54

 

 

 

25

 

75

24

 

 

34

 

 

 

1

75

 

 

 

25

 

 

60

 

 

24

63

 

 

15

Image 15
Contents Model No. WESY97310 Serial No QUESTIONS?Important Precautions Table of ContentsBefore You Begin DimensionsFour Stages of the Assembly Process AssemblyLocknuts yet Frame AssemblyPage Locknuts yet Nylon Locknut the Leg Press Lever must pivot easily Nylon Locknuts yetNylon Locknuts 50. Do not tighten the Nylon Locknuts yet Groove fits over the welded pin on the Weight TubeLocate and open the parts bag labeled ARM Assembly Arm AssemblyLarge Cable Trap is oriented as shown Cable AssemblySmall Pulley Bracket is oriented exactly as shown Pulley Plates are oriented as shown Bracket is oriented as shownMake sure the Cable Trap is oriented as shown Page Cable Trap is oriented as shown Remove a Pro Pulley 26 from the bag labeled Pulley BAGPulley and the welded pin on the Press Top Frame Page Make sure the Cable Trap is oriented as shown Page Locate and open the parts bag labeled Seat Assembly Seat AssemblyLeg Press Plate must be on the upper edge Miscellaneous AssemblyWeider Cable Diagrams Press Cable Changing the Weight Settings AdjustmentTightening the Cables Trouble-shooting and MaintenanceLeg Raise Weight Resistance ChartHigh Arm Leg Butterfly Curl Ab Pulley Press LbsPart Identification Chart-Model No. WESY97310 R0601A Page Page Qty Description Part List-Model No. WESY97310Drawing Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement Parts