12. Place two Weight Bumpers (51) over the indicated | 12 |
|
|
holes in the Weight Base (5). Slide a Weight Guide | 15 |
| |
|
| ||
(15) into each of the holes. |
|
|
|
Attach the indicated Weight Guide (15) to the Weight |
|
| 16 |
Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat |
|
| |
|
|
| |
Washers (48), and a 3/8” Nylon Locknut (50). |
| Groove |
|
|
|
| |
Slide ten Weights (21) onto the Weight Guides (15). |
| Pin |
|
Make sure the Weights are turned so the pin |
|
| |
|
| 70 | |
grooves point towards the floor. |
|
| |
|
|
| |
Press a Weight Tube Bumper (18) into the lower end |
|
| 18 |
of the Long Weight Tube (70). Slide the Weight Tube | Pin | 21 |
|
into the center holes in the Weights (21). |
|
| |
| Grooves |
|
|
Slide a Top Weight (16) onto the Weight Guides (15). |
|
|
|
Note: Make sure the Top Weight is turned so the |
|
|
|
groove fits over the welded pin on the Weight |
|
|
|
Tube (70). |
|
|
|
|
| 51 | 51 |
|
|
| |
|
|
| 48 |
|
|
| 50 |
|
| 48 |
|
| 46 |
| 5 |
13. Place the Weight Top Frame (66) on the indicated |
|
| |
|
|
| |
brackets on the Uprights (1 and 2). Note: The four |
|
|
|
Weight Guides (15) must be behind the Weight | 13 |
| 46 |
Top Frame, as shown in step 14. |
| 34 |
|
|
|
| |
Attach the Weight Top Frame (66) to the Butterfly Top | 46 |
| 50 |
Frame (33) with two 3/8” x 2 3/4” Bolts (46), a |
| ||
|
|
| |
Support Plate with 4” center holes (94), and two 3/8” |
|
| 66 |
Nylon Locknuts (50). Do not tighten the Nylon |
|
| |
94 |
|
| |
Locknuts yet. |
| 50 | |
|
|
| |
Attach the Weight Top Frame (66) to the bracket on | 33 |
| 15 |
the Butterfly Upright (1) with two 3/8” x 2 3/4” Bolts |
| ||
|
| ||
|
|
| |
(46), a Support Plate with 2 1/2” center holes (34), |
|
|
|
and two 3/8” Nylon Locknuts (50). Do not tighten the | 1 |
| Brackets |
Nylon Locknuts yet. |
|
|
|
14.Attach the Weight Top Frame (66) to the Press Top Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support Plate with 4” center holes (94), and a 3/8” Nylon Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable Trap (25) onto a 3/8” x 4” Bolt (78). Insert the Bolt through the Support Plate (94) and hand tighten a 3/8” Nylon Locknut (50) onto it.
Attach the Weight Top Frame (66) to the bracket on the Press Upright (2) with two 3/8” x 2 3/4” Bolts (46), a Support Plate with 2 1/2” center holes (34) and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon
Locknuts yet.
9
14 |
| 46 |
|
66 | 34 | 50 |
|
|
|
| |
|
| 50 |
|
| 9 | 94 |
|
|
| 46 | |
|
|
| |
|
| 25 |
|
|
| 24 | 78 |
|
| 2 |
|