Weider 8530 manual Cable Assembly Seat Assembly, Insets show view, From other side

Page 13

CABLE ASSEMBLY

SEAT ASSEMBLY

25.See inset drawing A. Note: The inset draw- ing shows the view from the other side of the Squat Arm Upright (56). Wrap the Long Cable (72) around a ÒVÓ-Pulley (50). Attach the ÒVÓ-Pulley and a Long Cable Trap (31) to the top hole in the Squat Arm Upright with the 3/8Ó x 5Ó Bolt (67), the 5/8Ó x 3/8Ó Spacer (76), a 3/8Ó Flat Washer (9), and a 3/8Ó Nylon Locknut (21). Position the Long Cable Trap (31) as shown.

See inset drawing B. Note: The inset draw- ing shows the view from the other side of the Squat Arm Upright (56). Slide the end of the Long Cable (72) onto the end of the 3/8Ó x 2 1/4Ó Bolt (94). Thread another 3/8Ó Jam Nut

(92)onto the Bolt. Do not tighten the sec- ond Jam Nut. There must be room between the two Jam Nuts for the end of the Cable to pivot.

26.Attach the Backrest (41) to the Front Upright (42) with two 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó Flat Washers (10).

27.Press a 1 1/2Ó Inner Cap (32) into the Seat Frame (36).

Insert a 1/4Ó x 2Ó Carriage Bolt (38) through the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4Ó x 3/4Ó Screws (18).

Insert the 1/4Ó x 2Ó Carriage Bolt (38) through the indicated hole in the Seat Frame (36). Tighten a 1/4Ó Nylon Locknut (2) with a 1/4Ó Flat Washer (10) onto the Carriage Bolt.

Attach the other end of the Seat (13) to the Seat Frame (36) with a 1/4Ó Flat Washer (10) and a 1/4Ó x 2Ó Machine Screw (81).

13

25

 

Insets show view

 

 

 

 

 

from other side

 

 

 

 

A

 

 

21

 

 

 

 

9

 

 

 

 

 

 

72

 

 

 

 

67

 

 

76

50

 

 

 

56

31

 

50

 

 

 

 

 

 

 

 

 

72

B 92

 

 

 

 

 

 

 

 

 

 

94

 

 

72

 

 

26

 

42

 

 

 

 

 

 

 

 

 

41

 

 

43 10

 

 

 

27

13

 

 

 

 

 

 

 

 

 

 

38

 

 

 

 

37

32

 

 

 

 

 

 

 

18

 

 

36

 

 

 

 

81

10

2

 

 

 

 

Image 13
Contents Model No. WESY85301 Serial No QUESTIONS?Customer HOT Line Mon.ÐFri., 6 a.m.Ð6 p.m. MSTImportant Precautions Table of ContentsBefore YOU Begin DimensionsFrame Assembly AssemblyChart located in the center of this manual Following Tools not Included are Required for AssemblyTighten all of the Nylon Locknuts used in steps 1Ð3 Nylon Locknuts yetTube are sitting in the pin grooves in the top Weight On each Arm. Arm identification is very Important for step Frame Assembly ARM AssemblyOn the Top Frame Right Arm is behind the indicated bracketBe sure that the ball is on the indicated Cable AssemblyBe sure that the end of the Cable with 3/8Ó Nylon Locknut Locate the Short Cable 23. RoutePulley and the crossbar on the Press Cable Assembly Cable Trap is turned to hold the Cable in place Insets show view Cable Assembly Seat AssemblyFrom other side Seat Assembly VKR Assembly VKR Assembly Decals Changing the Weight Setting HOW to USE the Home GYM SystemAttaching and Removing the Seat Weight Resistance ChartAttaching the LEG Lever to the LOW Pulley Station Tightening the Cables TROUBLE-SHOOTING and MaintenanceTightening the Medium and Short Cables Tightening the Long CableTOP View Cable DiagramQty Description Part LISTÑModel No. WESY85301Exploded Page 2 Inner Cap 32Ð4 Inner Cap 27Ð5 Outer Cap 51Ð2 Page Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT