Weider 8530 manual Cable Assembly, Be sure that the ball is on the indicated

CABLE ASSEMBLY

During steps 13 to 25, refer to the CABLE DIA-	13
GRAM on page 19 of this manual. Identify the				58
		55
three cables by their lengths, and note the
positions of the cable traps. IMPORTANT: Do
not overtighten the bolts and nuts securing
the pulleys. The pulleys must turn freely.
13. Locate the Medium Cable (58). Route the
Medium Cable around the indicated 3 1/2Ó		15		88
Pulley (15) attached to the Top Frame (55).
		Ball
Be sure that the ball is on the indicated		Hook
side of the Pulley and that the Cable is
between the Pulley and the hook. Tighten
the 3/8Ó x 3 3/4Ó Bolt (88) and the 3/8Ó Nylon
Locknut (not shown).
14. Wrap the Medium Cable (58) around a ÒVÓ-	14					86
Pulley (50). Attach the ÒVÓ-Pulley and a Long					58
Cable Trap (31) to the indicated bracket on						31
the Front Upright (42) with a 3/8Ó x 2 1/2Ó Bolt			31
(86) and a 3/8Ó Nylon Locknut (21). Be sure						50
		86
that the Long Cable Trap is positioned to
hold the Cable in place.
Route the Medium Cable (58) around the ÒVÓ-						Bracket
Pulley (50) on the Left Arm (47). Be sure that						21
the Cable is in the groove of the Pulley and						42
that the Long Cable Trap (31) holds the
		50
Cable in place. Tighten the 3/8Ó x 2 1/2Ó Bolt
			47
(86) and the 3/8Ó Nylon Locknut (not shown).
15. Route the Medium Cable (58) around the ÒVÓ-	15
Pulley (50) on the Right Arm (48). Be sure					86
		68	31			50
that the Cable is in the groove of the ÒVÓ-
Pulley and that the Long Cable Trap (31) is
positioned to hold the Cable in place.		20
Tighten the 3/8Ó x 2 1/2Ó Bolt (86) and the 3/8Ó
Nylon Locknut (not shown).		66
Route the Medium Cable (58) around the		21				48
3 1/2Ó Pulley (15) attached to the Pulley					15
Bracket (20). Be sure that the Cable is in
		58
the groove of the Pulley and that the Cable
Trap (66) holds the Cable in place. Tighten
the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó
Bolt (not shown). Tighten the 5/16" x 5Ó Bolt
(68) and the 5/16" Nylon Locknut (not shown).	16
Be sure that the Pulley Bracket swivels freely.
16. See the inset drawing. Attach a 3 1/2Ó Pulley
(15) and a Cable Trap (66) to the upper hole
in the Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó		15
Bolt (12) and a 3/8Ó Nylon Locknut (21). Be
sure that the Cable Trap is inside the Long	58					58
ÒUÓ-Bracket. (Note: This may come pre-
assembled.)		15
Route the Medium Cable (58) through the	66					57
		12
3 1/2Ó Pulley (15) and Long ÒUÓ-Bracket (57)	21
shown in the inset drawing. Be sure that the
Cable is in the groove of the Pulley and		57
that the Cable and Pulley move smoothly.
	9