Weider WESY81080 manual Cable Assembly, Nylon Jamnut. The Leg Lever should pivot freely

Page 10

13.Press a 1 1/2Ó Square Inner Cap (33) into the Leg Lever (29).

Lubricate a 5/16Ó x 2 1/2Ó Bolt (22). Attach the Leg Lever (29) to the Seat Frame (36) with the Bolt and a 5/16Ó Nylon Jamnut (80). Do not overtighten the

Nylon Jamnut. The Leg Lever should pivot freely.

Thread a 5/16Ó Plain Nut (32) halfway onto the 5/16Ó x 2Ó Eyebolt (44). Thread the Eyebolt into the Leg Lever (29). Tighten the Plain Nut to prevent the Eyebolt from turning.

Note: The use of remaining parts from the ARM ASSEMBLY parts bag will be explained in step 31.

Cable Assembly

14.Locate and open the parts bag labeled ÒCABLE ASSEMBLY AND PULLEYS.Ó For Cable identifica- tion and routing during steps 14Ð28, refer to the Cable Diagram and Cable ID Chart on page 16.

Locate the Short Cable (9). It is approximately 127Ò long. Wrap the end with the ball around a 3 1/2Ó Pulley (35) in the direction shown.

Attach the 3 1/2Ó Pulley to the Top Frame (1) with a 3/8Ó x 3 1/2Ó Bolt (54), a 3/8Ó Flat Washer (55) and a 3/8Ó Nylon Locknut (63).

Make sure the Short Cable (9) is between the Pulley (35) and the welded hook (K) on the Top Frame (1).

15.Wrap the Short Cable (9) around a ÒVÓ-Pulley (6) in the direction shown.

Attach the ÒVÓ-Pulley (6) and a Long Cable Trap (50) to the indicated bracket (J) with a 3/8Ó x 2 1/4Ó Bolt (65) and a 3/8Ó Nylon Locknut (63). Make sure the

Long Cable Trap is positioned as shown, so it will hold the Cable in place.

13

36

 

 

 

 

 

80

 

44

22 Lubricate

 

 

 

 

29

 

32

33

 

 

14

 

 

63

1

 

 

 

55

 

 

 

K

 

 

35

 

 

 

54

 

9

 

15

 

 

 

J

 

9

 

 

 

 

65

 

 

50

 

 

6

 

 

63

10

Image 10
Contents QUESTIONS? Model No. WESY81080 Serial NoTable of Contents Limited WarrantyImportant Precautions Before You Begin Assembly Four Stages of the Assembly ProcessFrame Assembly Do not tighten the Nylon Locknuts yetDo not tighten the Locknuts yet Locate and open the parts bag labeled Òarm ASSEMBLY.Ó Arm AssemblyTighten all Nylon Locknuts used in steps 3 through Tap two 1Ó Retainers 4 and a 1Ó Round Cover Cap Cable Assembly Nylon Jamnut. The Leg Lever should pivot freelyMake sure the Cable Trap 66 is positioned as shown Page Page Seat Assembly Locate and open the parts bag labeled Òseat ASSEMBLY.ÓMiscellaneous Assembly Cable ID Chart Long Cable Cable DiagramShort Cable Adjustment Changing the Weight SettingWeight Resistance Chart Trouble-shooting and Maintenance Tightening the CablesPart Identification ChartÑWESY81080 Page Page Exploded DrawingÑModel No. WESY81080 Part ListÑModel No. WESY81080 Qty DescriptionOrdering Replacement Parts