Weider WESY81081 manual Make sure the Cable Trap 66 is positioned as shown

Page 11

16.Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown.

Attach the 3 1/2Ó Pulley (35) and a Cable Trap (66) to the Left Butterfly Arm (47) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (63).

Make sure the Cable Trap (66) is positioned as shown.

Route the Short Cable (9) under the Top Frame (1) between the Pulley (35) and the crossbar.

17.Move to the other side of the unit. Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown.

Attach the 3 1/2Ó Pulley (35) and a Cable Trap (66) to the Right Butterfly Arm (48) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (63).

Make sure the Cable Trap (66) is positioned as shown.

18.Remove the 1/2Ó Nylon Locknut (68) from the welded bolt (L) on the Top Frame (1). Slide the Pulley Bracket (20) onto the bolt and secure it with the Nylon Locknut. Tighten the Locknut, but make sure the Pulley Bracket can pivot freely.

Remove the 3 1/2Ó Pulley (35) from the Pulley Bracket (20). Wrap the Short Cable (9) around the Pulley in the direction shown.

Re-attach the 3 1/2Ó Pulley (35) to the Pulley Bracket

(20)with the 3/8Ó x 1 3/4Ó Bolt (83) and the 3/8Ó Nylon Jamnut (57).

19.Move to the other side of the unit. Remove the 3 1/2Ó Pulley (35) attached to the Pulley Plates (31).

Wrap the Short Cable (9) around the 3 1/2Ó Pulley

(35)in the direction shown.

Re-attach the Pulley (35) to the Pulley Plates (31) with the 3/8Ó x 1 1/2Ó Bolt (60) and the 3/8Ó Nylon Jamnut (57).

16

 

1

9

66

62

 

Crossbar

 

 

 

 

35

63

 

 

 

47

17

 

 

66

62

 

 

9

 

35

 

 

 

 

63

 

 

48

18

 

1

 

 

L

 

 

20

 

83

57

 

 

68

 

 

35

 

 

9

 

 

19

 

 

 

 

9

35

 

57

60

 

 

31

 

 

11

Image 11
Contents Model No. WESY81081 Serial No QUESTIONS?Limited Warranty Table of ContentsImportant Precautions Before You Begin Four Stages of the Assembly Process AssemblyDo not tighten the Nylon Locknuts yet Frame AssemblyDo not tighten the Locknuts yet Locate and open the parts bag labeled Òarm Arm AssemblyPage Nylon Jamnut. The Leg Lever should pivot freely Cable AssemblyMake sure the Cable Trap 66 is positioned as shown Page Page Locate and open the parts bag labeled Òseat ASSEMBLY.Ó Seat AssemblyMiscellaneous Assembly Short Cable Cable DiagramCable ID Chart Long Cable Changing the Weight Setting AdjustmentWeight Resistance Chart Tightening the Cables Trouble-shooting and MaintenanceExploded DrawingÑModel No. WESY81081 Qty Description Part ListÑModel No. WESY81081Page Part Identification ChartÑWESY81081 Page Ordering Replacement Parts