Weider WESY81081 manual

Page 12

20. Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35)

20

 

 

 

in the direction shown. Attach the 3 1/2Ó Pulley (35) to

 

N

 

 

 

 

the front bracket (M) underneath the Top Frame (1)

63

M

 

 

with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut

62

 

 

 

(63). Make sure the Bolt (62) is inserted from the

1

 

 

 

direction shown on the drawing.

 

 

 

 

Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35)

 

 

63

62

in the direction shown. Attach the 3 1/2Ó Pulley (35) to

 

 

 

 

the rear bracket (N) underneath the Top Frame (1)

 

 

 

 

with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut

 

 

 

 

(63). Make sure the Bolt (62) is inserted from the

9

 

35

 

direction shown on the drawing.

 

 

 

 

 

 

 

21. Make sure the Short Cable (9) is in the groove of

21

 

 

 

all Pulleys and that the Cable and the Pulleys

 

 

 

 

 

 

 

move smoothly.

 

 

 

 

Attach the closed loop on the end of the Short Cable

9

 

53

 

 

 

 

(9) to the Weight Tube (25) with the 5/16Ó x 1 3/4Ó

 

 

25

 

Bolt (58) and a 5/16Ó Nylon Locknut (53). It will be

 

 

 

58

 

 

 

necessary to lift the Weight Tube and the Top Weight

 

 

 

 

 

 

 

to insert the Bolt through the Weight Tube and the

 

 

 

 

loop on the Cable.

 

 

 

 

22. Locate the Long cable (2). It is approximately 215Ó

22

42

 

 

long. Wrap the end with the ball around the Low

 

 

 

 

 

 

Pulley (40) in the direction shown. Attach the Pulley

55

 

 

 

to the bracket (O) on the Base (8) with a 3/8Ó x 2Ó

57

 

 

Bolt (62) and a 3/8Ó Nylon Locknut (63).

 

 

 

 

Thread the Long Cable (2) through the Press Frame

66

 

 

 

 

 

 

40

(12). Wrap the Long Cable around a 3 1/2Ó Pulley

 

 

 

 

 

 

 

(35) in the direction shown. Attach the Pulley to the

35

 

 

2

Front Upright (42) with a 3/8Ó x 3 1/2Ó Bolt (54), a

54

12

 

 

Cable Trap (66), a 3/8Ó Flat Washer (55) and a 3/8Ó

 

 

 

Nylon Jamnut (57).

 

8

O

63

 

 

 

62

 

23. Remove the free Pulley (35) attached to the Pulley

23

 

 

 

Plates (31). Wrap the Long Cable (2) around the

 

 

 

 

 

31

 

Pulley in the direction shown.

 

 

 

Re-attach the Pulley (35) to the Pulley Plates (31)

57

 

60

 

 

 

 

with the 3/8Ó x 1 1/2Ó Bolt (60) and the 3/8Ó Nylon

2

 

35

 

Jamnut (57).

 

 

12

Image 12
Contents QUESTIONS? Model No. WESY81081 Serial NoTable of Contents Limited WarrantyImportant Precautions Before You Begin Assembly Four Stages of the Assembly ProcessFrame Assembly Do not tighten the Nylon Locknuts yetDo not tighten the Locknuts yet Arm Assembly Locate and open the parts bag labeled ÒarmPage Cable Assembly Nylon Jamnut. The Leg Lever should pivot freelyMake sure the Cable Trap 66 is positioned as shown Page Page Seat Assembly Locate and open the parts bag labeled Òseat ASSEMBLY.ÓMiscellaneous Assembly Cable Diagram Cable ID Chart Long CableShort Cable Adjustment Changing the Weight SettingWeight Resistance Chart Trouble-shooting and Maintenance Tightening the CablesExploded DrawingÑModel No. WESY81081 Part ListÑModel No. WESY81081 Qty DescriptionPage Part Identification ChartÑWESY81081 Page Ordering Replacement Parts