Weider WESY37531 user manual Trap is turned to hold the Cable in place

Page 12

23.Remove the preassembled 3/8” x 2” Bolts (54) from one set of Adjustable Pulley Plates (23).

Wrap the Butterfly Cable (73) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable Trap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50). Be sure that the Cable

Trap is turned to hold the Cable in place.

24.Wrap the Butterfly Cable (73) around a “V”-Pulley

(27).Attach the “V”-Pulley and a Large Cable Trap

(32)to the bracket on the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt (87) and a 3/8” Nylon Locknut

(50).Be sure that the Cable Trap is turned to hold the Cable in place.

25.Attach the Butterfly Cable (73) to the Left Pivot Arm (71) with a 5/16” x 2 1/4” Shoulder Bolt (79) and a 5/16” Nylon Jamnut (34).

26.Locate the Ab Cable (47). Insert the Ab Cable up through the Press Top Frame (9) and wrap it around a 3 1/2” Pulley (24). Attach a 3/8” Flat Washer (48) and a 5/8” x 3/4” Bushing (66) to a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press Top Frame and the 3 1/2” Pulley. Secure another 5/8” x 3/4” Bushing and 3/8” Flat Washer to the Bolt with a 3/8” Nylon Locknut (50).

12

23

 

54

24

25

 

73

 

50

23

24

87

 

32

 

50

27

 

 

73

 

1

25

 

73

 

 

79

 

71

 

34

26

 

66

 

24

 

62

9

48

 

48

50

47

 

Image 12
Contents QUESTIONS? Model No. WESY37531 Serial NoTable of Contents Important Precautions Using the weight system. If you have additional Before YOU BeginFor your benefit, read this manual carefully before Assembly Make Assembly EasierFrame Assembly Nylon Locknuts yetDo not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Locate and open the parts bag labeled ARM Assembly Tighten the Nylon Locknuts 50 used in stepsPage Cable Assembly Nylon Jamnut the Leg Lever must pivot easilyTrap is turned to hold the Cable in place Page Weight Cable is in the groove of the 3 1/2 Pulley Cable Trap is turned to hold the Cable in place Cable Trap is turned to hold the Cable in place Locknut yet Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Adjustments Changing the Weight SettingAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart PlatesTroubleshooting Tightening the CablesCable Diagrams Weight Cable Cable ID Stack Low Pulley Page 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Part Identification CHART-Model No. WESY37531 R1003AX 4 Bolt X 4 3/4 Bolt X 5 1/2 Bolt Part LIST-Model No. WESY37531 Qty DescriptionModel No. WESY37531 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT