Weider WESY37531 user manual Cable Trap is turned to hold the Cable in place

Page 16

39.Wrap the Weight Cable (72) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable Trap (25) between the lowest holes in the Adjustable Pulley Plates (23) hanging from the Ab Cable (47) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50) that was removed in step 28. Be sure that the

Cable Trap is turned to hold the Cable in place.

40.Remove the preassembled 3/8” x 1 3/4” Bolts (57) from the Small Pulley Plates (22).

Wrap the Weight Cable (72) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley between two Small Pulley Plates (22) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50).

41.Wrap the Weight Cable (72) around a 4 1/2” Pulley (82). Attach the 4 1/2” Pulley to the bracket on the Press Top Frame (9) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).

42.Place a 1/2” Flat Washer (11) on top of the Weight Tube (17).

Thread a 1/2” Plain Nut (45) halfway onto the bolt on the Weight Cable (72). Screw the bolt on the Weight Cable into the Weight Tube (17) a couple of turns.

Tighten the 1/2” Plain Nut (45) down onto the 1/2” Flat Washer (11).

39

 

47

 

 

54

 

23

 

 

 

25

50

 

 

 

24

 

 

 

72

40

 

 

 

24

72

 

 

50

 

57

 

 

22

41

 

 

54

 

72

 

 

 

82

50

 

 

 

 

Bracket

9

 

 

42

 

 

 

72

 

 

45

 

 

11

 

 

17

 

16

Image 16
Contents QUESTIONS? Model No. WESY37531 Serial NoTable of Contents Important Precautions Before YOU Begin Using the weight system. If you have additionalFor your benefit, read this manual carefully before Assembly Make Assembly EasierFrame Assembly Nylon Locknuts yetDo not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Locate and open the parts bag labeled ARM Assembly Tighten the Nylon Locknuts 50 used in stepsPage Cable Assembly Nylon Jamnut the Leg Lever must pivot easilyTrap is turned to hold the Cable in place Page Weight Cable is in the groove of the 3 1/2 Pulley Cable Trap is turned to hold the Cable in place Cable Trap is turned to hold the Cable in place Locknut yet Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Adjustments Changing the Weight SettingAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart PlatesTroubleshooting Tightening the CablesCable Diagrams Weight Cable Cable ID Stack Low Pulley Page 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Part Identification CHART-Model No. WESY37531 R1003AX 4 Bolt X 4 3/4 Bolt X 5 1/2 Bolt Part LIST-Model No. WESY37531 Qty DescriptionModel No. WESY37531 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT