Weider WESY49310 user manual Must be inserted from the side shown

Page 17

CABLE ASSEMBLY

36. Slide a 5/16” Flat Washer (8) onto a 5/16” x

36

 

 

 

 

2 3/4” Bolt (11). Insert the Bolt through the indi-

 

 

 

 

 

 

 

 

 

cated hole in the Pivot Arm (101). The Bolt

 

 

 

 

 

must be inserted from the side shown.

 

 

 

 

 

Fully tighten a 5/16” Nylon Jam Nut (93) onto

21

 

 

 

 

the Bolt.

 

93

 

 

 

Wrap the Military Press Cable (72) around a

 

9

 

 

 

3 1/2” Pulley (15). Attach the Pulley and a

 

 

 

 

 

 

 

 

 

Cable Trap (66) to the Pivot Arm (101) with

 

 

 

 

 

the 3/8” x 3 3/4” Bolt (88), a 3/8” Flat Washer

 

 

8

 

 

(9), and a 3/8” Nylon Locknut (21). Be sure

 

101

11

 

 

 

 

that the Pulley is on the side shown and

 

 

 

 

 

 

 

 

that the Cable Trap is positioned to hold

 

72

 

 

 

the Cable in place.

 

 

 

 

 

15

 

 

 

 

 

66

88

 

 

 

 

 

 

 

 

 

 

37. See inset drawing A. Attach a 3 1/2” Pulley

37

 

 

 

 

(15) and a Cable Trap (66) to the upper hole

 

 

15

A

 

 

 

in a Long “U”-Bracket (57) with a 3/8” x 2”

 

 

 

 

 

Bolt (12) and a 3/8” Nylon Locknut (21). Be

 

21

 

 

66

sure that the Cable Trap is inside the Long

 

 

 

 

 

 

 

 

“U”-Bracket. (Note: This may come pre-

 

 

 

 

 

assembled.)

 

57

 

12

Route the Military Press Cable (72) through

 

 

 

 

 

 

 

the Long “U”-Bracket (57) and the 3 1/2”

 

 

 

 

B

Pulley (15). Be sure that the Cable is in the

 

93

 

 

groove of the Pulley and that the Cable

 

 

 

 

 

 

 

 

 

and Pulley move smoothly.

 

72

 

 

 

 

 

 

 

 

See inset drawing B. Slide the end of the

 

11

 

 

 

Military Press Cable (72) onto the end of the

15

57

 

 

 

5/16” x 2 3/4 Bolt (11). Thread another 5/16”

 

 

 

 

 

Nylon Jam Nut (93) onto the Bolt. Do not

72

 

 

 

 

fully tighten the second Jam Nut. There

 

 

 

 

 

 

 

 

 

must be room between the two Jam Nuts

 

 

 

 

 

for the end of the Cable to pivot.

 

 

 

 

 

17

Image 17
Contents QUESTIONS? Table of ContentsLocation shown Important PrecautionsApply the decal Before YOU Begin DimensionsFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyNylon Locknuts yet Tighten all Nylon Locknuts used in steps Weights 25 until is completeTube is sitting in the pin grooves in the top Weight ARM Assembly Frame Assembly ARM AssemblyDo not tighten the Nylon Locknut yet 101 Bracket 105 106 107 ARM Assembly Cable Assembly Nylon Locknut the Pulley Bracket Must be able to move freely Long Cable Trap is positioned to hold Cable in place102 Move smoothly Locate the Low Cable 23. Route the LowPulley and the crossbar on the Press Cable Assembly Cable Assembly Must be inserted from the side shown Locate the Leg Press Cable 99. Attach Locate and open the parts bag labeled Seat Assembly Seat AssemblySeat Assembly Seat Assembly Decal Changing the Weight Setting HOW to USE the Weight SystemAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceHigh Cable 58 and Low Cable Cable DiagramsHigh Cable Low CableLeg Press Cable Military Press Cable 72 and Leg Press Cable Pivot ArmWESY49310 R0901A 16 x 3 Bolt Page Qty Description Part LIST-Model No. WESY49310Exploded DRAWING-Model No Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty