Weider WESY49310 user manual TROUBLE-SHOOTING and Maintenance, Tightening the Cables

Page 25

TROUBLE-SHOOTING AND MAINTENANCE

Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

TIGHTENING THE CABLES

Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. If any slack is felt when using the front weight stack, both the High Cable (58) and the Low Cable (23) will need to be tightened. If any slack is felt when using the rear weight stack, both the Military Press Cable (72) and the Leg Press Cable (99) will need to be tightened.

To tighten the cables, insert the weight pin into the middle of the weight stack. Slack can be removed from these cables several ways:

See drawing 1. Tighten the 1/4” Nylon Locknut (2) that connects the end of the Low Cable (23) to the Long “U”- Bracket (57).

The Leg Press Cable (99) can be tightened in the same manner.

See drawing 1. Move the 3 1/2” Pulley (15) to the other hole in one of the Long “U”-Brackets (57). Remove the 3/8” Nylon Locknut (21) and the 3/8” x 2” Bolt (12) from the Cable Trap (66), Pulley, and Long “U”-Bracket. Re- attach the Pulley and Cable Trap. Be sure that the Cable Trap is in the proper position and that the Cable and Pulley move smoothly.

The other Long “U”-Bracket (57) can be adjusted in the same manner.

See drawing 2. Tighten the 1/4” Nylon Locknut (2) that connects the end of the High Cable (58) to the Small “U”- Bracket (71).

The Military Press Cable (72) can be tightened in the same manner.

See Drawing 3. If additional slack is felt while using the Leg Press Arm (96), then the end of the Leg Press Cable (99) must be moved to the next hole in the Rear Seat Frame (100). Remove the 5/16” x 2 3/4” Bolt (11), the 5/16” Flat Washer (8), the end of the Cable, and both 5/16” Nylon Jam Nuts (93) from the Rear Seat Frame. Re- attach the Bolt, the Washer, the end of the Cable, and both Nylon Jam Nuts to the next hole in the Rear Seat Frame.

1

 

66

15

 

21

 

57

12

 

2

23 or 99

2

 

72

58

 

71

 

2

71

 

 

2

3

 

 

96

 

11

 

8

 

100

 

99

 

93

 

93

Do not overtighten the cables; the top weight will be lifted off the weight stack.

If a cable tends to slip off the pulleys often, it may have become twisted. Remove the cable and re-install it.

If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

25

Image 25
Contents QUESTIONS? Table of ContentsApply the decal Important PrecautionsLocation shown Before YOU Begin DimensionsFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyNylon Locknuts yet Tighten all Nylon Locknuts used in steps Weights 25 until is completeTube is sitting in the pin grooves in the top Weight ARM Assembly Frame Assembly ARM AssemblyDo not tighten the Nylon Locknut yet 101 Bracket 105 106 107 ARM Assembly Cable Assembly Nylon Locknut the Pulley Bracket Must be able to move freely Long Cable Trap is positioned to hold Cable in place102 Pulley and the crossbar on the Press Locate the Low Cable 23. Route the LowMove smoothly Cable Assembly Cable Assembly Must be inserted from the side shown Locate the Leg Press Cable 99. Attach Locate and open the parts bag labeled Seat Assembly Seat AssemblySeat Assembly Seat Assembly Decal Changing the Weight Setting HOW to USE the Weight SystemAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceHigh Cable 58 and Low Cable Cable DiagramsHigh Cable Low CableLeg Press Cable Military Press Cable 72 and Leg Press Cable Pivot ArmWESY49310 R0901A 16 x 3 Bolt Page Qty Description Part LIST-Model No. WESY49310Exploded DRAWING-Model No Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT