Weider WESY49310 user manual Locate the Leg Press Cable 99. Attach

Page 18

CABLE ASSEMBLY

38. Locate the Leg Press Cable (99). Attach the

38

 

 

end of the Leg Press Cable to the Long “U”-

 

 

 

2

 

Bracket (57) with a 1/4” Nylon Locknut (2) and

 

 

a 1/4” Flat Washer (10). Do not completely

 

 

 

tighten the Nylon Locknut. It should be

 

 

 

threaded onto the end of the Cable only a

 

 

57

couple of turns, as shown in the inset

 

 

 

drawing.

 

10

 

 

 

 

Wrap the Leg Press Cable (99) around a

 

 

 

3 1/2” Pulley (15). Attach the Pulley to the Leg

 

 

 

Press Upright (56) with the 3/8” x 3 3/4” Bolt

 

99

 

(88), a 3/8” Flat Washer (9), and a 3/8” Nylon

 

56

Locknut (21). The ball on the Cable must be

 

 

 

 

 

on the indicated side of the Pulley. Be sure

 

88

Ball

that the Cable and Pulley move smoothly

 

15

and that the Cable is between the Pulley

 

 

 

 

 

and the welded rod.

 

 

 

 

 

 

9

 

 

 

21

 

 

 

Welded

 

 

2

Rod

 

 

 

 

 

10

 

 

99

57

 

 

 

 

39. Attach the Press Bracket (94) to the Leg

39

 

 

Press Arm (96) with a 5/16” x 3” Bolt (111)

 

 

 

 

 

and a 5/16” Nylon Locknut (3).

 

 

 

Wrap the Leg Press Cable (99) around a 3 1/2”

 

 

 

Pulley (15). Attach the Pulley to the Press

 

 

 

Bracket (94) with the 3/8” x 2” Bolt (12) and a

 

 

 

3/8” Nylon Locknut (21).

 

 

96

Slide a 5/16” Flat Washer (8) onto a 5/16” x

 

 

12

 

 

3

2 3/4” Bolt (11). Insert the Bolt through the

11

 

 

 

lowest hole in the Rear Seat Frame (100)

 

8

94

 

 

from the indicated side. (Note: The three

 

99

111

holes are for cable adjustment.) Tighten a

 

 

 

5/16” Nylon Jam Nut (93) onto the Bolt. Slide

 

15

the end of the Leg Press Cable (99) onto the

 

end of the Bolt. Thread another 5/16” Nylon

 

 

21

 

 

 

Jam Nut onto the Bolt. Do not fully tighten

 

 

 

the second Jam Nut. There must be room

 

 

 

between the two Jam Nuts for the end of

 

 

 

the Cable to pivot.

 

100

 

 

 

 

93

18

Image 18
Contents Table of Contents QUESTIONS?Important Precautions Apply the decalLocation shown Dimensions Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyFrame Assembly Frame AssemblyNylon Locknuts yet Weights 25 until is complete Tighten all Nylon Locknuts used in stepsTube is sitting in the pin grooves in the top Weight Frame Assembly ARM Assembly ARM AssemblyDo not tighten the Nylon Locknut yet 101 Bracket 105 106 107 ARM Assembly Cable Assembly Long Cable Trap is positioned to hold Cable in place Nylon Locknut the Pulley Bracket Must be able to move freely102 Locate the Low Cable 23. Route the Low Pulley and the crossbar on the PressMove smoothly Cable Assembly Cable Assembly Must be inserted from the side shown Locate the Leg Press Cable 99. Attach Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Assembly Seat Assembly Decal HOW to USE the Weight System Changing the Weight SettingAdjusting the LEG Press Plate Attaching and Removing the SeatAttaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesHigh Cable Cable DiagramsHigh Cable 58 and Low Cable Low CableMilitary Press Cable 72 and Leg Press Cable Pivot Arm Leg Press CableWESY49310 R0901A 16 x 3 Bolt Page Part LIST-Model No. WESY49310 Qty DescriptionExploded DRAWING-Model No Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT