Weider WESY49310 Frame Assembly, Following Tools not Included are Required for Assembly

Page 4

ASSEMBLY

Before beginning assembly, carefully read the following information and instructions:

•Place all parts of the weight system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.

•The assembly is divided into four stages: 1) frame assembly, 2) arm assembly, 3) cable and pulley assembly, and 4) seat and backrest assembly. The hardware for each stage is pack- aged separately.

•Wait until you begin each assembly stage to open the parts bag labeled for that assembly stage.

•For help identifying the small parts used in assembly, use the PART IDENTIFICATION

CHART located in the center of this manual.

Note: Some small parts may have been pre- attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

•As you assemble the weight system, be sure that all parts are oriented as shown in the drawings.

•Tighten all parts as you assemble them, unless instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY:

•Two (2) adjustable wrenches

•One (1) standard screwdriver

•One (1) phillips screwdriver

• One (1) rubber mallet

•Lubricant, such as grease or petroleum jelly, and soapy water will also be needed.

Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

FRAME ASSEMBLY

1.Before beginning assembly, be sure that you have read and understand the infor- mation in the box above.

Locate and open the parts bag labeled

“FRAME ASSEMBLY.”

Press two 2” Square Outer Caps (51) onto the Stabilizer (5). Press a 2” Square Inner Cap (27) into the Base (4).

Insert six 5/16” x 2 1/2” Carriage Bolts (1) up through the Stabilizer (5). Insert two 5/16” x 2 1/2” Carriage Bolts up through the Base (4).

Attach the Base (4) to the Stabilizer (5) with two 5/16” x 2 3/4” Bolts (11), two 5/16” Flat Washers (8), and two 5/16” Nylon Locknuts

(3). Do not tighten the Nylon Locknuts yet.

1

 

 

 

 

 

11

 

 

 

51

 

 

 

 

 

 

8

 

5

 

 

 

 

 

 

 

 

1

51

1

3

 

 

 

 

 

4

1

 

 

 

 

 

 

 

 

27

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Table of Contents QUESTIONS?Apply the decal Important PrecautionsLocation shown Dimensions Before YOU BeginAssembly Frame AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyNylon Locknuts yet Weights 25 until is complete Tighten all Nylon Locknuts used in stepsTube is sitting in the pin grooves in the top Weight Frame Assembly ARM Assembly ARM AssemblyDo not tighten the Nylon Locknut yet 101 Bracket 105 106 107 ARM Assembly Cable Assembly Long Cable Trap is positioned to hold Cable in place Nylon Locknut the Pulley Bracket Must be able to move freely102 Pulley and the crossbar on the Press Locate the Low Cable 23. Route the LowMove smoothly Cable Assembly Cable Assembly Must be inserted from the side shown Locate the Leg Press Cable 99. Attach Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Assembly Seat Assembly Decal HOW to USE the Weight System Changing the Weight SettingAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesCable Diagrams High Cable 58 and Low CableHigh Cable Low CableMilitary Press Cable 72 and Leg Press Cable Pivot Arm Leg Press CableWESY49310 R0901A 16 x 3 Bolt Page Part LIST-Model No. WESY49310 Qty DescriptionExploded DRAWING-Model No Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents