Basic operations
|
|
|
|
|
|
|
|
|
|
| SOURCE SELECTOR | MASTER VOLUME |
| DIMMER | SETTING | ADJUST | SURROUND |
|
|
|
|
| SET / TUNER PRESET | / MULTI JOG |
|
|
|
|
|
|
|
|
|
|
|
|
| PHONES |
STANDBY / ON | STANDBY |
|
|
| DVD MULTI | DVD | DBS | VCR | TV | FM / AM |
|
|
CAUTION:
Be sure to turn down the volume:
•Before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.
•Before removing headphones, as high volume may output from the speakers.
HOME CINEMA CONTROL CENTER
OPEN/CLOSE |
| KARAOKE |
| AUDIO | |
AUDIO/TV | DVD |
| |||
/VCR/DBS |
|
|
| ||
DVD |
| VCR | DBS | TV | |
DVD |
| VCR | DBS | TV | |
DVD MULTI | FM/AM | TV/VIDEO | MUTING | ||
TV VOL | CHANNEL | VOLUME | |||
TUNING |
| FM MODE | TUNING | ||
| MEMORY |
|
|
| |
TOP MENU |
|
|
|
| MENU |
|
| ENTER |
|
| |
CHOICE |
|
|
|
| ON |
|
|
|
| SCREEN | |
AUDIO |
| ECHO | RESERVE | RETURN | |
SUBTITLE | TITLE/GROUP | ||||
KARAOKE SOUND | BASS |
| TREBLE | ||
ZOOM |
| 1 | 2 |
| 3 |
PROGRESSIVE |
| BASS |
| TREBLE | |
VFP |
| 4 | 5 |
| 6 |
KARAOKE |
|
|
|
|
|
|
| 7 | 8 |
| 9 |
KEY TV RETURN |
|
| 100+ | ||
ANGLE |
| 10 | 0 |
| +10 |
KEY |
| VOCAL | EFFECT |
| |
REPEAT |
| 3D |
|
|
|
DIMMER |
| SLEEP ANALOG/DIGITAL CANCEL | |||
|
|
| INPUT |
| |
SMART S. SETUP | BASS BOOST |
|
| A.POSITION | |
|
|
| TONE |
| |
|
|
|
|
| SURROUND |
TEST |
| EFFECT | DECODE |
| |
SUBWFR | CENTER | L | SURR R | ||
When operating the receiver using the remote control, always set the mode selector to AUDIO/TV/ VCR/DBS.
Selecting the digital decode mode
If the following symptoms occur while playing Dolby Digital or DTS Digital Surround software with “DGTL AUTO” selected (see page 13), follow the procedure below:
•Sound does not come out at the beginning of playback.
•Noise comes out while searching for or skipping chapters or tracks.
From the remote control ONLY:
1Press ANALOG/DIGITAL INPUT to select “DGTL AUTO.”
2Press DECODE to select “DGTL D.D.” or “DGTL DTS.”
•Each time you press the button, the digital decode mode changes as follows:
L | C | R |
|
SUBWFR LFE |
| ||
DOLBY D |
|
|
|
LS |
| RS | VOL |
3 Adjust the volume
To increase the volume, turn MASTER VOLUME control clockwise (or press VOLUME + on the remote control).
To decrease the volume, turn MASTER VOLUME control counterclockwise (or press VOLUME – on the remote control).
CAUTION:
Always set the volume to the minimum before starting any sources. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
NOTE
The volume level can be adjusted within the range of “0” (minimum) to “50” (maximum).
Listening with headphones
Connect a pair of headphones to the PHONES jack on the front panel. This cancels the Surround mode currently selected, deactivates speakers, and activates the HEADPHONE mode. The HP (headphone) indicator lights up on the display.
•Disconnecting a pair of headphone from the PHONES jack cancels the HEADPHONE mode and activates the speakers.
HEADPHONE mode
When using the headphones, the following signal is output regardless of your speaker setting:
—For 2 channel sources, the front left and right channel signal is output directly from the left and right headphones.
—For
You can enjoy
DGTL AUTO |
| DGTL D.D. |
|
DGTL DTS
•To play back software encoded with Dolby Digital, select “DGTL D.D.”
•To play back software encoded with DTS Digital Surround, select “DGTL DTS.”
NOTE
When you turn off the power or select another source, “DGTL DTS” or “DGTL D.D.” is canceled and the digital decode mode is automatically reset to “DGTL AUTO.”
The following are the analog/digital signal format indicators on the display to indicate what type of signal comes into the receiver.
ANALOG: Lights when analog input is selected.
LPCM: Lights when Linear PCM signal comes in.
DOLBY D: • Lights when Dolby Digital signal comes in.
•Flashes when “DGTL D.D.” is selected for software not encoded with Dolby Digital.
DTS: • Lights when DTS signal comes in.
•Flashes when “DGTL DTS” is selected for software not encoded with DTS.
NOTE
When “DGTL AUTO” cannot recognize the incoming signal, no digital signal format indicator lights up on the display.
14