JVC LVT1002-012B manual Using DSP modes, Repeat steps 5 and 6 to adjust the other settings

Creating realistic sound fields

CENTER*1: To adjust the center speaker output level

(from –10 dB to +10 dB).

SURR L*1: To adjust the left surround speaker output level (from –10 dB to +10 dB).

SURR R*1: To adjust the right surround speaker output level (from –10 dB to +10 dB).

PANORAMA control*2:

•Select “ON” when you would like to enjoy

“wraparound” sound effect with side-wall image.

•Select “OFF” when you would like to hear originally recorded sound.

*1 “0” is the initial setting for each speaker setting. *2 “OFF” is the initial setting.

Using DSP modes

Once you have adjusted the DSP modes, the adjustment is memorized for each source.

•You cannot use the DSP modes if no surround speakers are connected.

•You cannot adjust the effect level for “ALL CH ST.”

When operating this receiver using the remote control, always set the mode selector to AUDIO/TV/VCR/DBS.

Before you start, remember...

Make sure that you have set the speaker information correctly (see pages 16 to 19).

6Turn MULTI JOG to adjust the item selected in step 5, then press SET.

Your setting is stored.

•When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.

L R PL ΙΙ

LPCM SUBWFR

VOL

Ex.: When selecting “+8 (dB)” for “CENTER.”

7Repeat steps 5 and 6 to adjust the other settings.

To cancel Surround mode

Press SURROUND repeatedly on the remote control or press SURROUND then turn MULTI JOG on the front panel so that “STEREO” appears on the display.

•If Surround mode is canceled while playing back multi-channel digital software, all channel signals are mixed and output through the front speakers (and subwoofer if you have connected a subwoofer and set the subwoofer setting correctly—“USE” for Quick Setup or “YES” for Manual Setup—see pages 17 and 18).

From the remote control:

KARAOKE SOUND		BASS	TREBLE
ZOOM	1	2	3	It will be convenient for you to use
		BASS	TREBLE
VFP	4	5	6	the remote control for the sound
KARAOKE	7	8	9
				adjustments, since you can make
KEY TV RETURN			100+
ANGLE	10	0	+10	adjustments from your listening
KEY	VOCAL	EFFECT
REPEAT	3D			point, and use the test signal.
DIMMER	SLEEP ANALOG/DIGITAL CANCEL
		INPUT
SMART S. SETUP	BASS BOOST		A.POSITION
		TONE
			SURROUND
TEST	EFFECT	DECODE
SUBWFR	CENTER	L	SURR R

1Start playing 2 channel software—either Linear PCM or analog signal—and select the source.

2Press SURROUND repeatedly until one of the DSP modes you want to apply appears on the display.

The DSP indicator lights up on the display.

•Each time you press the button, the DSP modes change as follows:

L R

LPCM SUBWFR DSP

VOL

	NOTES
•	You can adjust the speaker output levels using the remote control
	without outputting the test tone.
•	You cannot adjust the center speaker output level and no test tone	3
	comes out of the center speaker when “CNTR SP” is set to “NO.”

•You cannot adjust the surround speaker output levels and no test tone comes out of the surround speakers when “SURR SP” is set to “NO.”

•Remember not to change the speaker setting while using any Surround modes; otherwise, the Surround mode may be canceled when you deactivate the speakers required for it .

•You cannot use any Surround modes when selecting DVD MULTI as a playback source.

PLII MOVIE	PLII MUSIC
LIVE CLUB	DANCE CLUB
HALL	PAVILION
ALL CH ST.	STEREO (Surround/DSP off)
(Back to the beginning)

Press TEST to check the speakers output balance.

“TEST L” starts flashing on the display, and a test tone comes out of the speakers as follows:

L R

LPCM SUBWFR DSP

VOL

TEST L TEST C TEST R

(Left front speaker) (Center speaker) (Right front speaker)

TEST LS TEST RS

(Left surround speaker) (Right surround speaker)

30