JVC LVT1002-001B manual Effect available only for DAP modes *2, To adjust the DAP effect level

Creating realistic sound fields

4Adjust the surround speaker output levels (from –10 dB to +10 dB).

•Make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.

To adjust the left surround speaker level,

press SURR L +/–.

To adjust the right surround speaker level,

press SURR R +/–.

L R

LPCM SUBWFR DSP

VOL

Ex.: When selecting “–8 (dB)” for “SURR R.”

5Press TEST again to stop the test tone.

6Only for DAP modes:

Press EFFECT to select the DAP effect level (1 to 5) you want.

•As the number increases, the DAP effect becomes stronger (normally set it to “EFFECT 3”).

L R

LPCM SUBWFR DSP

VOL

5Turn MULTI JOG until the setting item you want to set appears on the display, then press SET.

•As you turn MULTI JOG, the indication changes as follow:

L R

LPCM SUBWFR DSP

VOL

BASS	TREBLE		SUBWFR
CENTER	SURR L		SURR R
EFFECT*	PANORAMA			BAL
B.BOOST	ATT	(Back to the beginning)

* Available only for DAP modes.

SURR L*1: To adjust the left surround speaker output level (from –10 dB to +10 dB).

SURR R*1: To adjust the right surround speaker output level (from –10 dB to +10 dB).

EFFECT (available only for DAP modes) *2:

To adjust the DAP effect level.

As the number increases, the effect becomes stronger (normally set it to “EFFECT 3”).

*1 “0 (dB)” is the initial setting for each speaker setting. *2 “3” is the initial setting.

EFFECT 3 EFFECT 4 EFFECT 5

EFFECT 2 EFFECT 1

On the front panel:

•No test tone is available when using the buttons on the front panel.

SOURCE SELECTOR

MASTER VOLUME

TV DIRECT

SETTING

ADJUST

SURROUND

SET / TUNER PRESET

/ MULTI JOG

PHONES

STANDBY / ON

STANDBY

DVD MULTI

DVD

STB

VCB

TV

FM / AM

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

6Turn MULTI JOG to adjust the item selected in step 5, then press SET.

Your setting is stored.

•When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.

L R

LPCM SUBWFR DSP

VOL

Ex.: When selecting “–8 (dB)” for “SURR R.”

7Repeat steps 5 and 6 to adjust the other settings.

1Start playing 2 channel software—either Linear PCM or analogue signal—and select the source.

2Press SURROUND.

MULTI JOG now works for the Surround/DSP mode selection.

3Turn MULTI JOG until one of the DSP modes you want to apply appears on the display.

The DSP indicator lights up on the display.

•As you turn MULTI JOG, the indication changes as follow:

L R

LPCM SUBWFR DSP

VOL

PL II MOVIE	PL II MUSIC
LIVE CLUB	DANCE CLUB
HALL	PAVILION
ALL CH ST.	STEREO (Surround/DSP off)
(Back to the beginning)

4Press ADJUST.

MULTI JOG now works for the sound adjustment.

To cancel DSP Modes

Press SURROUND repeatedly on the remote control or press SURROUND then turn MULTI JOG on the front panel so that “STEREO” appears on the display. The DSP indicator goes off from the display.

NOTES

•You can adjust the speaker output levels using the remote control without outputting the test tone.

•You cannot adjust the center speaker output level and no test tone comes out of the center speaker when “CNTR SP” is set to “NO.”

•You cannot adjust the surround speaker output levels and no test tone comes out of the surround speakers when “SURR SP” is set to “NO.”

33