JVC LVT1002-001B manual Troubleshooting, Problem Possible Cause Solution, General

Page 70

Troubleshooting

Use this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC’s service center.

RX-ES1SL

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not come on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

No sound from speakers.

Speaker signal cables are not connected.

 

An incorrect source is selected.

 

Muting is activated.

 

An incorrect input mode (analogue or

 

digital) is selected.

 

Connections are incorrect.

 

TV Direct is activated.

Check speaker wiring and reconnect if necessary.

Select the correct source.

Press MUTING to cancel the mute.

Select the correct input mode (analogue or digital).

Check connections.

Deactivate TV Direct (see pages 13 and 20).

Buttons cannot be used.

TV Direct is activated.

Deactivate TV Direct (see pages 13 and 20).

 

 

 

Sound from one speaker only.

The balance is set to one extreme.

Adjust the balance properly (see page 21).

 

 

 

 

The STANDBY lamp lights up after

Speakers are overloaded because of high

1. Press STANDBY/ON

on the front panel to turn

turning on the power, but soon the unit

volume.

off the unit.

 

turns off (into standby mode).

 

2. Stop the playback source.

 

 

3. Turn on the unit again, and adjust the volume.

 

Speakers are overloaded because of a

Check the speaker wiring.

 

 

short circuit at the speaker terminals.

If speaker wiring is not short-circuited, contact your

 

 

dealer.

 

 

 

 

 

The unit is overloaded because of a high

Consult your dealer after unplugging the power cord.

 

voltage.

 

 

“OVER HEAT” flashes on the display,

The unit is overheated because of high

Turn on the unit again. If the unit turns off soon,

then the unit is turned off.

volume or long time usage.

consult your dealer after unplugging the power cord.

 

 

 

Remote control does not operate as

The remote control is not ready for your

Press a source selecting button or TONE first, then

you intend.

intended operation.

press the buttons you want to use. (See pages 21,

 

 

62, 63 and 64.)

 

 

 

 

 

Remote control does not work.

There is an obstruction hiding the remote

Remove the obstruction.

 

 

sensor on the unit.

 

 

 

Batteries are weak.

Replace batteries.

 

 

The mode selector is set to the incorrect

Set the mode selector to the proper position.

 

position.

 

 

 

 

 

Bass sound is reinforced too much

Appropriate bass level is not selected.

Adjust audio position level (see page 22).

when listening in stereo.

 

 

 

General

65

Image 70
Contents RX-ES1SL XV-N55SL LVT1002-001BIf in Doubt Consult a Competent Electrician Important for Laser Products Reproduction of LabelsXV-N55SL RX-ES1SLDo not stack XV-N55SL and RX-ES1SL Above ALL Table of Contents When operating the player XV-N55SL, set the mode Remote controlWhen operating the receiver RX-ES1SL, set the mode Selector h to AUDIO/TV/VCR/STBRear panel Parts identificationFront panel Display windowFront panel AV OUT Video Signal SelectorDisplay window COAXIAL, OpticalPutting batteries in the remote control PrecautionsChecking the supplied accessories Getting startedFM antenna connection Connecting the FM and AM MW antennasGetting started FM antenna suppliedConnecting the subwoofer Connecting the speakers and DVD playerSpeaker Layout Diagram Connecting the front, center, and surround speakersDigital connection Connecting other video componentsConnecting the DVD player XV-N55SL STB Set Top BoxScart connection Monaural Connecting the power cordAnalogue connection for DVD Multi playback see DVD Multi playback is not available for XV-N55SLSelecting the analogue or digital input mode Turn on the powerTo turn off the power into standby Basic operationsListening with headphones Adjust the volumeSelecting the digital decode mode Basic operationsActivating TV Direct To cancel TV Direct and turn off the receiver, pressTo restore the sound, press Muting again Turning off the sounds temporarily- MutingSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Changing the display brightnessFrom the remote control only Speaker settingsTV/VCR/STB Speaker settings When selecting Medium Room Setting the speakers sizeOperating procedure When selecting Large RoomSetting the low frequency effect attenuator -LFE Setting the speaker delay timeSetting the crossover frequency-CROSS Setting the dynamic range compression -D.COMPDigital 3DVD player Initial setting Basic settingsOperating procedure Digital 2STBSetting the Auto Function mode-MODE Setting Auto Surround-AUTO SRBasic settings Adjusting the subwoofer output level Sound adjustmentsAdjusting the tone-BASS, Treble Press AdjustSound adjustments Adjusting the front speakers output balance-BALAttenuating the input signal-ATT Setting the subwoofer audio positionTo store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsTo tune in a preset station Selecting the FM reception modeTuner operations Press Display while listening to an FM station Using the RDS Radio Data System to receive FM stationsWhat information can RDS signals provide? Frequency RT Normal indicationPress PTY Search while listening to an FM station To search for a program using the PTY codesDescription of the PTY codes PTY codesTA Traffic Announcement in your area Switching to broadcast program of your choice temporarilyNone TA/NEWS/INFO NEWS/INFO News NewsIntroducing the Surround/DSP modes Creating realistic sound fieldsReproducing theater ambience Surround modesCreating realistic sound fields DSP Digital Signal Processor modesAvailable Surround/DSP modes for each input signal DAP Digital Acoustic Processor modesUsing Surround modes Dolby D or DTS Stereo Surround/DSP offPress Test again to stop the test tone Turn Multi JOG to select a appropriate surround modePress Test to check the speakers output balance Select and play software you like Press SurroundAlways set the mode selector to AUDIO/TV/VCR/STB Using DSP modesRepeat steps 5 and 6 to adjust the other settings To cancel Surround modeTo cancel DSP Modes To adjust the DAP effect levelEffect available only for DAP modes *2 From the remote control Press DVD Multi Using the DVD Multi playback modeAdjusting the speaker output level Turn Source Selector until DVD Multi appears on the displayAbout this manual Before operationAbout discs Initial setup Turning on/off the playerIf a menu is shown on the TV screen To bring up the DVD Player SET UP display laterBasic playback About PBC Playback ControlResuming playback Various speed playback Locating the beginning of a scene or song Using the numeric buttonsTo replay the previous scenes One touch replay function Locating a desired scene from the DVD menu Advanced operationsPlaying from a specific position Specifying a desired titleAdvanced operations Changing the playback orderTo play back in a specific order Program play To dismiss the menu barTo play back in random order Random play To stop repeat playback Repeat playbackTo repeat a desired part A-B repeat playback To quit repeat playbackTo change the audio language or sound Audio Changing the language, sound and scene angleTo select a scene angle of DVD Video Angle To zoom in pictures To adjust the picture character VFPSpecial picture/sound effect To return to the normal playbackTo simulate surround sound 3D Phonic Basic operation procedureMenu bar functions To bring up the menu barMenu bar functions for SVCD/Video CD/ Audio CD Time mode selectionMenu bar functions for DVD Video CHAP. Chapter searchAbout MP3/WMA discs MP3/WMA disc playbackOperations Basic operationsDirect selection Repeat playbackMP3/WMA disc playback Basic operations Jpeg disc playbackAbout Jpeg discs To see a desired pictureTo start the slide show Viewing pictures continuously slide show modeTo zoom in the picture To select the start point of the slide showWhile the Jpeg Control display is shown, press Repeat Press Repeat mode remains activeRepeat function Press 3 to start repeat playbackSelecting preferences Changing the initial settingsHow to set preferences About the Preference displayLanguage menu Changing the initial settingsPicture menu Audio menu Others menuBring up the Others menu Limiting playback by childrenTo set Parental Lock for the first time Press 5/∞ to move To select Parental Lock then press EnterPress 5/∞ to move To select Parental Lock and press Enter To change the settingsTo temporarily release the Parental Lock Press 5/∞ to move to Temporary RELEASE, then press EnterAppendix a Country/Area code list for Parental Lock Additional informationFor Appendix C Digital output signal chartFor pages 45 Output Disc typeAppendix D Glossary Operating other JVC products DVD playerTry to operate your STB by pressing STB Changing the transmittable signals for operating anOperating other manufacturers’ equipment Manufacturer CodesOperating other manufacturers’ equipment Changing the transmittable signals for operating aChanging the transmittable signals for operating a Try to operate your VCR by pressing VCRProblem Possible Cause Solution TroubleshootingGeneral FM/AM Problem Possible Cause Solution TroubleshootingSurround/DSP Standard Video ActiveRGB/COMP Operation Picture AudioFM tuner IHF SpecificationsAmplifier AM MW tunerOther SpecificationsAudio characteristics Video outputs 2003 Victor Company of JAPAN, Limited 0203NHMMDWJEIN

LVT1002-001B specifications

The JVC LVT1002-001B is a versatile and user-friendly remote control designed to enhance the experience of JVC audio and video products. Its sleek design and intuitive layout make it an indispensable accessory for users looking to navigate their entertainment systems seamlessly.

One of the most notable features of the JVC LVT1002-001B is its compatibility with a wide range of JVC devices. Whether you are operating a television, DVD player, Blu-ray player, or sound system, this remote control provides comprehensive functionality, eliminating the need for multiple remotes cluttering your living space. This universal compatibility makes it an ideal solution for households that utilize various JVC products.

The remote features a well-organized button layout, allowing users to access the most frequently used functions with ease. Large, clearly labeled buttons for volume control, channel selection, and playback functions ensure that users can make adjustments without hassle. Additionally, the remote includes dedicated buttons for quick access to settings and source selection, further enhancing its usability.

Among its advanced technologies, the LVT1002-001B employs infrared (IR) technology, which allows for reliable communication between the remote and the targeted JVC devices. This ensures that commands are executed promptly, providing a smooth and responsive user experience. Moreover, the remote is built with durable materials, designed to withstand everyday use, making it a long-lasting component of your audio-visual setup.

The JVC LVT1002-001B also includes features such as a range of programmable buttons, allowing users to personalize their experience. This means users can set up macros for their favorite activities, like watching a movie or listening to music, where multiple commands can be executed with a single button press, streamlining the entertainment experience.

Furthermore, the remote is designed with energy efficiency in mind. It uses standard batteries that are easy to replace, ensuring that users can keep their remote functional without hassle. The battery life is optimized to last longer, reducing the frequency of replacements and contributing to a more eco-friendly lifestyle.

In summary, the JVC LVT1002-001B remote control combines functionality, durability, and user-friendly features into one device, making it an essential tool for anyone looking to enhance their JVC audio and video experience. Its universal compatibility, intuitive design, and programmable options highlight its role as a key accessory for modern entertainment systems.