Whirlpool W10151492B manual Install VentSystem, Install LevelingLegs, Connect Vent, LevelDryer

Page 14

Vent system chart

NOTE: Performance of rear exhaust to either side of the dryer is equivalent to adding one elbow. To determine maximum exhaust length, add one elbow to the chart.

Number of

Type of

Box or

Angled

90º turns

vent

Louvered

hoods

or elbows

 

hoods

 

 

 

 

 

0

Rigid metal

64 ft (20 m)

58 ft (17.7 m)

 

 

 

 

1

Rigid metal

54 ft (16.5 m)

48 ft (14.6 m)

 

 

 

 

2

Rigid metal

44 ft (13.4 m)

38 ft (11.6 m)

 

 

 

 

3

Rigid metal

35 ft (10.7 m)

29 ft (8.8 m)

 

 

 

 

4

Rigid metal

27 ft (8.2 m)

21 ft (6.4 m)

Install VentSystem

1.Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

2.Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp.

3.Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into the interior of the vent to secure the vent, because they can catch lint.

Install LevelingLegs

3.Examine the leveling legs. Find the diamond marking.

4.Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.

5.Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.

Connect Vent

1.Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (102 mm) clamp.

2.Move dryer into its final location. Do not crush or kink vent.

3.(On gas models) Check that there are no kinks in the flexible gas line.

4.Once the exhaust vent connection is made, remove the corner posts and cardboard.

LevelDryer

Check the levelness of the dryer by first placing a level on the top of the dryer near the console.

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1.To protect the floor, use a large, flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2.Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on the cardboard. See illustration.

Then, by placing a level in the crease on the side of the dryer between the top of the dryer and the dryer cabinet, check the levelness from front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

14

Image 14
Contents System Electric Dryer W10151492B SP PN W10151493BDryer Safety Table of ContentsPage LocationRequirements Installation InstructionsToolsandParts ElectricalRequirements U.S.A.Only Mobile home Additional installation requirementsMobile home installations require Electrical ConnectionIf connecting by direct wire ElectricalRequirements-CanadaOnlyStyle 1 Power supply cord strain relief Power Supply Cord Direct WireInstall strain relief ElectricalConnection U.S.A. OnlyWire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct Wire CG F Optional 3-wire connection If this is a new vent system Vent material If using an existing vent systemVentingRequirements Plan VentSystem Alternate installations for close clearancesSpecial provisions for mobile home installations Determine vent pathVent system chart Install VentSystemInstall LevelingLegs Connect VentReverseDoorSwing Remove the door assemblyReinstall the door Reverse the strikeCanada Complete InstallationU.S.A If the dryer will not start, check the followingStartingYourDryer Press PAUSE/CANCELDryer USE To use an Automatic CycleStatusLights Stopping,Pausing,orRestartingDryingandCycleTips Cycles Modifiers Options EndofCycleSignal DryingRackOptionDryer Care DryerOperation TroubleshootingChangingtheDrumLight Lint on load Dryer ResultsCycle time too short IntheU.S.A Assistance OrserviceAccessories InCanadaWhirlpool Corporation Laundry Warranty This limited warranty does not coverSécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteConservez CES Instructions Outillageetpièces Instructions D’INSTALLATIONExigencesd’emplacement Exigencesconcernant l’évacuation Linstallation dans une maison mobile exigeSpécifications électriques Pour le Canada seulement ’est à l’utilisateur qu’incombe la responsabilité deEn cas dutilisation du système dévacuation existant Déterminer litinéraire dacheminement du conduit Autres installations où le dégagement est réduitPlanification du système d’évacuation Une réduction de la longévité de la sécheuseRaccordement du conduit d’évacuation Installation dusystème d’évacuationInstallation des pieds de nivellement Réglage de l’aplomb de la sécheuseDépose de la porte Réinstallation de la porteInversion du sens d’ouverture de la porte Inversion de la gâcheSi la sécheuse ne démarre pas, vérifier ce qui suit Achever l’installationFermer la porte vérifier l’engagement de la gâche Voir DépannageUtilisation dun programme automatique Utilisation DE LA SécheuseMiseenmarchedelasécheuse Pour mettre la sécheuse en pause ou larrêter à tout moment Arrêt, pause ou remise en marcheConseils pour le séchage et les programmes Pour remettre la sécheuse en marcheTémoins lumineux ProgrammesModificateurs Signal de fin de programme Changement des programmes après avoir appuyé sur Start Changement des programmes Modificateurs et optionsOption de grille de séchage Modification des préréglages de niveau de séchageNettoyage avant chaque charge Nettoyagedel’emplacementdelasécheuseNettoyagedufiltreàcharpie Nettoyagedel’intérieurdelasécheuse RetraitdelacharpieaccumuléeRésultatsdelasécheuse DépannageFonctionnementdelasécheuse Taches sur la charge ou sur le tambour Temps de programme trop courtCharpie sur la charge Charges avec faux plisPour plus d’assistance AccessoiresSi vous avez besoin de pièces de rechange La présente garantie limitée ne couvre pas Composer leW10151492B SP PN W10151493B

W10151493B, W10151492B specifications

The Whirlpool W10151492B and W10151493B are high-performance refrigerator water filters designed to enhance the quality of drinking water and ice while maintaining the overall health and safety standards for your household. These models are compatible with a range of Whirlpool refrigerators and provide an efficient solution for reducing contaminants commonly found in tap water.

One of the main features of the W10151492B and W10151493B is their advanced filtration technology. Employing an activated carbon filtration system, these filters are capable of reducing harmful impurities such as chlorine, lead, mercury, pesticides, and pharmaceuticals. This not only improves the taste and odor of the water but also ensures that it is safe for consumption, making these filters an ideal choice for families looking to consume clean, refreshing water directly from their refrigerator.

Another defining characteristic of these filters is their focus on convenience and user-friendliness. Designed for easy installation and replacement, both models come with clear instructions to ensure that users can effortlessly replace the filter themselves. This eliminates the need for professional installation services, making maintenance simpler and more accessible for the average consumer.

The W10151492B and W10151493B filters also boast a high capacity, with the ability to filter up to approximately 200 gallons of water, depending on water quality and usage. This long-lasting capability aids in reducing the frequency of filter replacements, thus minimizing both cost and environmental impact.

In addition to their functional benefits, these filters are certified by the National Sanitation Foundation (NSF), affirming that they meet stringent public health and safety standards. This certification provides peace of mind to consumers, ensuring that their filtration system is not only effective but also trustworthy.

Moreover, the W10151492B and W10151493B demonstrate an eco-conscious approach; they help reduce reliance on bottled water, contributing to less plastic waste in landfills. Choosing these filters represents a smart choice for environmentally aware households.

In summary, the Whirlpool W10151492B and W10151493B filters stand out with their combination of advanced filtration technology, ease of installation, long-lasting capacity, and certification by NSF. These features work together to provide clean, safe, and great-tasting water, catering to the needs of modern households who prioritize health, convenience, and sustainability.