ElectricalRequirements U.S.A.Only | Whirlpool W10151493B manual

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 mm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:

Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door, and floor moldings.

Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Companion appliance spacing should also be considered.

Additional spacing is required if you exhaust out the rear of the dryer to either the right or left side.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

This dryer is manufactured ready to install with a 3-wire

14" max.*	48 in.2 *
(356 mm)	48 in.2 *
18"*	(310 cm2 )
(457 mm)
	24 in.2 *
	(155 cm2 )

29"

1"*

29¼"

(25 mm)

(737 mm)

(25 mm)

(25 mm) (743 mm)

(127

mm)

3"*

(76 mm)

3"*

(76 mm)

electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.

If local codes do not permit the connection of a neutral ground wire to the neutral wire, see “Optional 3-wire connection” in “Electrical Connection - U.S.A. Only” section.

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

*Required spacing

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA- Z240 MH.

Mobile home installations require:

Metal exhaust system hardware, which is available for purchase from your dealer.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

ElectricalRequirements - U.S.A.Only

It is your responsibility

To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.

A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations,

(2)mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover.

W10151493B, W10151492B specifications

The Whirlpool W10151492B and W10151493B are high-performance refrigerator water filters designed to enhance the quality of drinking water and ice while maintaining the overall health and safety standards for your household. These models are compatible with a range of Whirlpool refrigerators and provide an efficient solution for reducing contaminants commonly found in tap water.

One of the main features of the W10151492B and W10151493B is their advanced filtration technology. Employing an activated carbon filtration system, these filters are capable of reducing harmful impurities such as chlorine, lead, mercury, pesticides, and pharmaceuticals. This not only improves the taste and odor of the water but also ensures that it is safe for consumption, making these filters an ideal choice for families looking to consume clean, refreshing water directly from their refrigerator.

Another defining characteristic of these filters is their focus on convenience and user-friendliness. Designed for easy installation and replacement, both models come with clear instructions to ensure that users can effortlessly replace the filter themselves. This eliminates the need for professional installation services, making maintenance simpler and more accessible for the average consumer.

The W10151492B and W10151493B filters also boast a high capacity, with the ability to filter up to approximately 200 gallons of water, depending on water quality and usage. This long-lasting capability aids in reducing the frequency of filter replacements, thus minimizing both cost and environmental impact.

In addition to their functional benefits, these filters are certified by the National Sanitation Foundation (NSF), affirming that they meet stringent public health and safety standards. This certification provides peace of mind to consumers, ensuring that their filtration system is not only effective but also trustworthy.

Moreover, the W10151492B and W10151493B demonstrate an eco-conscious approach; they help reduce reliance on bottled water, contributing to less plastic waste in landfills. Choosing these filters represents a smart choice for environmentally aware households.

In summary, the Whirlpool W10151492B and W10151493B filters stand out with their combination of advanced filtration technology, ease of installation, long-lasting capacity, and certification by NSF. These features work together to provide clean, safe, and great-tasting water, catering to the needs of modern households who prioritize health, convenience, and sustainability.