Whirlpool 8535840 installation instructions Moving dryer to a new location?, Snap-Lock fittings

Page 12

CRUSH

TM

RESISTANT

Dura Safe

 

SURE CONNECTTM Vent Kit

Kits Make Installation Easy

Periscopes For Offset

Outlets, Tight Installations

For more information, or to have your venting professionally installed, call the Consumer Assistance Center. Check your Use and Care Guide for a toll-free

Provides 4 1/2"

clearance between

dryer and wall

Snap-Lock fittings

Total kit length 8 feet

Additional vent can

be snapped between

sections for

Provides 2 1/2" clearance between dryer and wall

Great for closet installations

0"-18", 18"-29" or 29"-50" periscopes include one male snap-lock fitting, one extra

long draw-band collar and one clamp

2 1/2"

21/2"

0"-18" : Part #4396037

18"-29" : Part #4396011

29"-50" : Part #4396014

number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Pages of your phone directory under “Appliances

— Household — Major — Service and Repair.”

Part #4396028

longer runs

 

Kit Contains:

2 - 4' vent sections with attached close elbows

1 - Wall plate for close clearance installations

2 - 4" clamps

.

Dura Safe and Sure Connect are Trademarks of Whirlpool, U.S.A.

0"-18" Periscope

Use when vent outlets overlap or are offset

Excess length can

be trimmed to fitPart #4396037

18"-29" and 29"-50" Periscope

 

 

 

 

Sections separate,

Swivel collar

 

fittings can face

 

same or opposite

wall connection

 

 

Telescoping

 

Swivel collar

sections

 

 

 

 

 

 

 

Extra long

Beveled edges

 

 

band-clamp

 

 

for dryer

allow corner

 

 

connection

installations

 

 

 

 

 

 

 

 

 

 

 

18"-29" : Part #4396011

 

29"-50" : Part #4396014

Moving dryer to a new location?

Check with a licensed electrician to confirm that supply voltage at new home matches voltage specified on the model/serial rating plate.

Shut off electrical supply to dryer. Unplug power supply cord and tape it securely to dryer. (Or disconnect power supply cable from dryer.)

Slide dryer onto cardboard or hardboard before moving it across the floor to prevent damaging floor covering.

Tape lint collector lid to cabinet.

Tape top to cabinet.

Tape door to front panel.

Turn leveling legs all the way in.

Part No. 8535840

 

 

© 2002 Whirlpool Corporation

Benton Harbor, Michigan 49022, U.S.A.

Printed in U.S.A.

Image 12 Contents
Installation Instructions Have questions about your dryer?Tools needed for installation Parts supplied for installationYour safety and the safety of others are very important For proper drying performanceParts needed for installation Venting systemElectrical Closet/confined area installation 43-1/8 38-1/4 Terminal block coverRecommended ground method Quincy, MassachusettsInstallation Mobile home installation requirementsPlan the exhaust vent Determine vent lengthInstall vent system If installing washer and dryer, install dryer firstPrepare the dryer Maximum length of the exhaust system depends uponPower supply cord Direct wireElectrical connection Hold-down screw Terminal Block coverFour-wire connection Remove center terminal block screwGround conductor screw. Tighten screw Tighten strain relief screwsThree-wire connection Where local codes permit10-30R Three-wire receptacle Loosen or remove center terminal block screwWhere local codes Do Not permit Level and exhaust dryerCheck operation ClampMoving dryer to a new location? Whirlpool Corporation Benton Harbor, Michigan 49022, U.S.ASnap-Lock fittings Instrucciones de instalación Lea y conserve estas instruccionesHerramientas que se necesitan para la instalación Para el debido funcionamiento de la secadoraEs su responsabilidad SignificanSistema de salida de aire Piezas para adquirirEléctrico Campana exterior de salida de aireInstalación en área empotrada Vista de frente 38,1 cm PulgMétodo recomendado de puesta a tierra Exterior de salida deDetermine la longitud del conducto Requisitos de instalación en una casa móvil o rodanteLa secadora debe fijarse al piso PreferidoInstale el sistema de ventilación nueva instalación Prepare de la secadoraLa longitud máxima del sistema de salida de aire depende de Marca de romboAlambre directo Conexión eléctricaTornillo de retención Cubierta del Bloque Terminal Conexión de cuatro alambres Preparación del alambreConexión de tres alambres Cuando los códigos locales lo permitenContacto 10-30R de tres alambres Cuando los códigos locales No lo permiten Abrazadera de 10.2 cm 4 pulg¿Va a trasladar de lugar la secadora?