JVC TH-A10R manual Analog connections, Video component connections, Analog component connections

Page 12

Connections

Connecting Audio/Video Components

You can connect the following audio/video components to this system.

Refer also to the manuals supplied with your components. Audio Components: Cassette deck or MD recorder* Video Components: TV or DBS tuner*

VCRs

*You can connect these components using the methods described in “Analog connections” (see below) or in “Digital connections” (see page 9).

Analog connections —————————————

Analog component connections

Use the cable with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, and the red plug to the audio right jack.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and the center unit, the sound output through this system may be distorted.

Cassette deck or MD recorder

Video component connections —————————

Use the cable with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the composite video jack. If your video components have S-video (Y/C-separation) terminals, connect them using S-video cable (not supplied).

Connecting these video components through the S-video input/ output terminal will give you better picture playback (or recording) quality.

IMPORTANT

This system is equipped with both the composite video and S-video input/output terminals for connecting video components.

You do not have to connect both the composite video and S-video terminals.

However, remember that the video signals from the composite video input terminals are output only through the composite video out terminals, while the ones from the S-video input terminals are output only through the S-video output terminals.

Therefore, if a recording video component and a playing video component are connected to the center unit through the different video terminals, you cannot record the picture from the playing component on the recording component. In addition, if the TV and a playing video component are connected to the center unit through the different video terminals, you cannot view the playback picture from the playing component on the TV.

VCR

Notes:

•When the DSP mode is ON, the VCR OUT (REC) jack and the TAPE/MD OUT (REC) jack will output surround sound to the front speakers only.

When recording, turn the DSP mode OFF (see page 21).

•You can connect either a cassette deck or a MD recorder to the TAPE/MD jacks. When connecting a MD recorder to the TAPE/ MD jacks, change the source name, which will be shown on the display when selected as the source, to “MD”. See page 17 for details.

If your audio components have a COMPU LINK-3 terminal

•See also page 54 for detailed information about the connection and the COMPU LINK-3 remote control system.

8

Page 11 Page 13
Image 12
Page 11 Page 13
Contents TH-A10R Class Laser Product Compu Link terminals 54 AC power cord supplied Analog audio input and output terminals 8System cable supplied Front right speakerAdjusting the angle of the satellite speakers Satellite speaker Center speaker Front left stpekerNon-slip rubber Satellite speaker rear left speaker Tilting the speaker to the frontTable of Contents Checking the supplied accessories Safety precautionsGetting Started Important cautionsSystem outline Center speaker SP-XCA10 Front left speakerFront right speaker Rear right speakerInstallation SpeakerTo hang satellite speakers from the wall ExampleAbout discs Playable disc typesDisc structure Video CDs with Playback Control functionConnecting the FM and AM MW Antennas To connect the powered sub-wooferConnecting the TV ConnectionsConnecting the rear and center speakers To connect speakersConneceting the front speakers Center speakerAnalog connections Video component connectionsAnalog component connections If your audio components have a Compu LINK-3 terminalDigital connections TV soundConnecting the power cord Light up the primary remote control buttonsPlug the power cord into an AC outlet Center unit Power sub-wooferPowered sub-woofer Parts IdentificationCenter unit Display windowRemote controls Primary remote controlOperation with the remote control Principles of operationTo operate via the on-screen menu Displaying the on-screen menuOn-screen menu components Basic operation with the on-screen menuOn-screen menus On-screen menus for using discs Preventing screen burn-out with Screen saver Screen SaverOpening screens DVD Control display VCD Control display For DVDTo turn the system power supply On and OFF standby To turn TV power on and OFFAdjusting volume Basic operationsMuting the sound Selecting the source to playChanging the source name Press one of the source selecting buttonsSelecting the analog or digital input Mode Changing the decode modeAdjusting the Input Signal Level Sub-woofer volume control Phase settingAudio channel display lamp Using the Sleep Timer Using the DSP ModesPress Sleep repeatedly To check or change the time remaining until Shut-off timePress DSP Mode Before recording a digital source, turn off the DSP modeWhen selecting DAP DAP modesUsing the DVD player To play a discPausing Locating the beginningResuming playback Selecting playback from the DVD menuPress ¢or Press Resume during playbackVideo CD menu To specify the title or track number for PlaybackTo play from the beginning of a title Chapter, or track To specify the chapter number for Playback CHAP. SearchTo specify the time for playback Press DVD on ScreenTo select the screen for playback from Digest screen Digest Press DigestUse the number buttons 0~9 to enter the time To display Continuous Photos Strobe Slow-Motion Playback SlowHold down FF/¢or 4/REW for more than 2 seconds Press Pause at the section you wish to view in slow motionUsing the Subtitle button Zooming a scene ZoomChanging the Subtitle Language Press ZoomChanging the audio channel Audio Use 5/cursors to move the pointer SubtitleUse 5/cursors to move the pointer to Audio Use 2/3/5/cursors to select the desired angle Press Enter Selecting a scene angle from the on-screen displaySelecting an angle from the angle list display Press and hold Angle for more than 1 secondsSelecting the Picture Character Or all tracks RepeatSampling all tracks Intro Use 5/cursors to move the pointer toProgramming the Playing Order Tracks Program Use 5/cursors to move the pointer to Time SelectUse 5/cursors to move the pointer Program and press Enter Random Play Random Press Play to start program playUse 5/cursors to move the pointer Random Quitting programmed playbackTuning in stations manually Using preset tuningReceiving radio broadcasts Selecting the FM reception mode When an FM stereo broadcast is hard to receive or noisyPress FM Mode Beat cutTo search for a program using the PTY codes Receive FM stationsSearching for a program by PTY codes Press PTY Search while listening to an FM stationChoice temporarily PTY codesTo stop listening to the program selected by EON Performing miscellaneous settings DVD settings on-screen displayMain Menu Sound Menu Speaker MenuMain Menu Settings Setting the Sleep TimerOpening the Main Menu Changing the DSP Mode Adjusting the volumeMove the pointer to Decode Mode using the 5/ cursors Sound Menu Settings Adjusting the balanceUsing Loudness Opening the Sound MenuAdjusting input signal Adjusting the DSP effectSpeaker Menu Settings Switching speaker modeOpening the Speaker Menu Setting speaker size Use the 2/3cursors to select Speaker SizeSet speaker size Speaker parametersAdjusting delay time Adjusting delay timeDVD Menu Settings Opening the DVD MenuChoosing menu language Change source to DVD, and stop playbackOn-screen guide settings Move the pointer to Audio Language usingChoosing audio language Choosing subtitle languageScreen saver settings Select monitor typeLB Letter Box Conversion PS Pan-scan ConversionLimiting playback by children Parental lock levelPress Enter while holding down Stop GB for country code and press EnterTo change the settings To temporarily release the Parental lockHow to handle discs Maintenance of discsCare and handling of discs Label sideCompu Link Remote Control System Remote Control through the Remote Sensor on the center unitAutomatic Source Selection To operate JVC’s audio components using this remote control To operate JVC’s video components using this remote controlOperating JVC’s Audio/Video Components Cassette deck MD recorderVCR TV VOL +Enter manufacturer’s code two digits using Press TV/DBSRelease TV Try to operate your TV by pressing TVPress VCR Try to operate your VCR by pressing VCRRelease ~ 10, 0, 100+ +10 Selects the TV channelsTroubleshooting Problem Possible Cause SolutionSpecifications Powered Sub-woofer SP-PWA10Center unit XV-THA10R Satellite Speakers SP-XSA10Appendix a Table of languages and their abbreviations Appendix B Country code list for parental lock Page 0600TNMNATJSC
Top Page Image Contents